Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The diverter motor was leaking
Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain. I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!
The right top side rack can apart. Wasn't able to reassemble.
I turned off the power to dishwasher first. Removed bottom plate to get to leveling legs. Lowered the legs as to be able to pull and skid dishwasher out from under counter. Once dishwasher is removed from under locate the 4 screws on right side that hold racks remove them. I would recommend replacing both skids on both side while you have the dishwasher pulled out. Very easy to replace new rack slid once old rack removed. The rack come assembled with skid and plastic holders. This repair is a 10 minute repair per side. Thanks Bob Seese
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
First, I bought the door balance link to replace the broken links that connect to the springs.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring. The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
The small knobs wore off that hold upper rack on the "drawer" guides.
I watched online repair video for replacing the part. 3 different clips held the part in place. Video showed how to properly remove each clip & also how to put them back on once part is replaced. Video was immensely helpful because I was afraid I break something else trying o remove them! I ordered & replaced the part by myself without help from my husband. My daddy would've been so proud. :)
Kids loved to make squeaky sounds opening and closing the doors, finally snapped the door balance link on one side.
1) clear out the dishwasher 2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top 3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection 4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online 5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides 6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point 7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them 8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame 9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly 10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame 11) you've done it! 12) have a cuppa and do your second washer that hasn't failed yet - it will soon.