Dishwasher Upper Rack Adjuster WPW10546503

Hi Gary, Thank you for your question. Yes, it would be the same for both sides. I hope this helps. Thank you and have a great day!

Hi Randy, Thank you for the question. Yes, the Rack Adjuster comes with the knob that ride in the metal channel. Hope this helps!

Hi Philip, thank you for your question. Unfortunately no. You would have to order two. Good luck with your repair.

Hi Val, Thank you for your inquiry. Before beginning any repair please unplug the dishwasher and wear gloves to protect your hands. Release the track stops from the upper dishrack rails and pull the upper rack from the dishwasher and place it upside down on a work surface. Raise the wheels to the maximum height. Release the top of the long rear clip from the dishrack tine and push the clip down to the release point and remove it. Press the tab down on the front clip move the clip up to pull it off. Release the locking tabs on the clip in the middle of the height adjuster and remove the clip. Using a slot screw driver pry the housing cover down and out to release the upper tabs on each side. Pry the bottom of the housing cover out of the 2 lower locking tabs. Pull the housing cover off the rack. Remove the adjuster housing and wheel assembly and repeat the procedure on the other side. Slide the vertical portion on the new wheel assembly between the fourth set of vertical tines from the back of the dishrack and rotate the wheel assembly so that it lays flat against the side. Insert a positioner clip above the rear wheel and snap the tab into the slot. Install a positioner clip on the front wheel. Position the adjuster body over the vertical portion of the wheel assembly and push in into the slots. Locking tabs at the bottom of the adjuster body engage the the wheel assembly once it is fully inserted the tabs. Insert the actuator lever into the adjuster body with the thumb pad facing the front of the rack. Two half circle cut outs on the adjuster body hold the actuator in place. Push the adjuster body down and install the adjuster cover. Install the adjuster cover mounting screws. Repeat this process on the other side of the rack. Push the upper dishrack onto its tracks. Close the track stops on the rails and the repair is done. I hope this helps. Thank you and have a great day!

Hello Mark, Thank you for your inquiry. At this time, we do not have a video for this exact part number but I have found instructions for you. Use a small flat head screwdriver to depress the retaining tabs securing the rack adjustors to the tracks. Fully remove the upper rack. Using the flat blade screwdriver, release the tabs to detach the adjuster housing cover and remove the housing. Next detach the front and rear adjuster support straps from the tines and remove them from the rack adjuster. Note the orientation of the rack adjuster, then pry off the stop clip to detach the old adjuster. Install the new adjuster by aligning it on the rack and snap the stop clip into place to secure. Next replace the front and rear support straps. Position the adjuster housing by aligning the locking lever in the adjuster slot then snap the cover on to secure. Then put the upper rack back into place. Hope this helps!

Hello Violet, Thank you for your inquiry. You would locate your model number on the left edge of the dishwasher's door, on the upper left hand corner of the unit's frame, on the top of the door jamb-to the left, right, or in the center, on the door itself, to the left, right or in the center, or on the underside of the control panel. Hope this helps!

Hello Rochelle, Thank you for the question. I suggest putting the rack back to the normal setting in height to see if the door will close. If the door closes you may need to replace the adjuster. It might be causing the rack to come forward and not allow the door to close properly. Hope this helps!

Hello Havilah, thank you for your question. The upper rack roller is part of the T shaped adjuster that attaches to the rack itself. The new rack adjuster kit provided by the manufacturer provides all the replacement parts for the right and left sides of that rack. The part number PartSelect Number PS10065979 will be the adjuster kit you need to order. I hope this helps!

Hello, thank you for your inquiry. This is the part that is listed as compatible with your model, and will work for both the left and the right side. We hope this helps!

Hi Elton, thank you for the great question. We have found that the part you mentioned does not come with both sides and is sold separately. This part is only available in plastic, it does not come in stainless steel. We hope this information helps!