KDTE104ESS4 KitchenAid Dishwasher - Instructions

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

Was easy to do but would recommend getting the 4 bolts that hold both racks in. The ones on the left side had rusted and hard to remove and reuse

Remove entire top rack and place on a large flat work surface. A small screwdriver is needed to release several plastic clips holding the upper drawer slider brackets and manifold in place. Carefully pry the clips free of their mounting holes and remove the bracket. Take some time to study how things are held together before removing anything since one plastic clip is closely affected by the others. Without pictures, and a video, it's really difficult to put into words. I must stress, do not force anything. When disassembling, use the opposite side to as a visual aid to reassemble.

Followed instruction via YouTube video. The video instructs to pry on the tabs to remove the dispenser - actually, just bend them out of the way with a screwdriver or putty knife. Once the dispenser is out, you can use pliers to bend the tabs back before installing the new dispenser. The only thing I would add is how to re-install the seal strip along the top edge. It has a groove in it that must be installed over the top edge of the outer cover BEFORE you screw the inner door to the outer cover. This was not clearly explained in the video.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

Removed screws holding dishwasher in place. This dishwasher has one one the left and right side after you open the door hidden behind a plastic hole cover that you can pry out of place with a putty knife or some other thin tool. After this pull the dishwasher out about halfway and there are 4 screws on each side of the dishwasher (on the outside) that hold the top track assemble. Just unscrew these with the appropriate sized socket, remove the old track and screw in the new track. Super easy. Anybody can do this.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

Located drain pump under dishwasher disconnected electrical from wall and pump twisted pump to remove, and installed new pump. Great customer service from Parts Select, helped to make sure i was ordering the correct part.

Replaced upper rack adjuster on both sides as these adjusters seem brittle due to heated drying over years. Followed YouTube video for repair. Very easy to fix.

Replaced the detergent dispenser on the door. Followed YouTube video with slight modification given moderate difference in model on video and my model. Relatively easy repair that takes a little bit of time.

Removed old part and replaced with new part

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

watched video took less than 5 min to replace veeeery easy to do

Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch

I followed the video on the site and it worked perfectly!