KBXR463EB0WW General Electric Dryer - Instructions

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....

My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

inserted the lint catcher into the opening to replace the old one

Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.

With the help of doityourself guy on the internet

Removed top panel giving access to drum and screws that hold front panel (door). Removed to screws to be able to remove front panel but be careful wires are short not giving you much room to remove panel. Removed plastic Drum Bearing and replaced with New one. Installed slides and put back together.

All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.

installation exactly how your directions told me on the computer