KBSD606ESS00 KitchenAid Refrigerator - Instructions

I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part installed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay

Removed old filter and installed new filter.

Go first to Kitchenaid web site and download their consumer services Technical diagnostics on the ice maker. Very well written and clear to follow. Instructions step you through interpretation of blinking code lights which is key to finding the real problem and leads you to repair the correct failed part. My diagnosis said to replace both emitter and receiver. I replaced the emitter first and tried it and solved the problem I didn't need to buy the receiver but I have a spare part now. Do the diagnosis and save yourself some money. PartSelect got the parts to me quickly and saved me money compared to our local parts supply companies.

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

I did some research on the website and found out that there is a test with the sensor lights. When I looked at mine, they were not turning on or blinking when the door was openned.

The repair was very easy to accomplish and all I needed was a small philiips screwdriver. I unscrewed both left and right side panels covering the circuit boards and pulled the connector off. I'd say the most diffcult part was lining up the connectors to the boards since there's not a lot of room because of the harness length. Once the boards were connected, they set in place easy and I put the covers back on.

A word of warning, it took the system about ten minutes until the cycle started and water started filling the tray. But aside from that, everything is working perfectly well.

I saved about $200 in service fees!!

Over the last several years we have had several appliance repairmen try to fix the icemaker. One replaced the entire icemaker. We bought a booster pump for the water. After spending about $1,000 over the past few years trying to fix the problem, a plumber doing routine plumbing work looked at it, and said it might be the control board. I found instructions online how to test the control boards. I ran the test, and they failed. I ordered the parts from PartSelect, followed their easy instructions, and tested the new units. They passed with flying colors. We now actually have an automatic icemaker for the first time in years.

Followed the instruction video.

I had to remove ice storage compartment sitting above motor on door to expose auger gear. Then used a small socket to remove 4 screws from underside of auger motor compartment in door. Motor drops out with a small wiring harness attached. This simply unplugs and then swaps in with new motor. Auger axel was sanded to remove rust and grease applied. Motor door and ice compartment were then reattached.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

diagnosed the problem to be the emitter and receiver boards. replaced in about 15 minutes. works like new!

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!

Watched video of similar model repair for filter housing. But the model KitchenAide refrigerator requires enter and replacing housing from the back. My model has a metal facing which has doors attached to it also. It was simple repair though from the backside of the appliance.

Just needed to replace the water filter

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.