KBSD606ESS00 KitchenAid Refrigerator - Instructions

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.

Bought new applicator

filter has to be removed and attached then inserted into rifrigerator

Do not try to pull out the water filter by the cap. There is a button that releases the filter so you will not have to replace the cap. The cap twists onto the filter. When replacing the filter, the cap goes onto the new one.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old motor unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.

The repair went just as simple as the video on the web site. Parts came really fast. replaced in less than 15 minutes. i thought the icemaker unit was the bad part but after gettin info from this site it told me waht to check first and i found that the emitter boards were bad. Thanks for saving me the money on buying the wrong parts. also bought parts the folowing week to repair my wifes kitchenaid mixer.

Replaced the light that was out.
Problem fixed

The ice maker would not fill with water. Water was available to in-door water dispenser. All signs pointed to the ice maker control boards. Ordered and replaced the boards. Within a couple hours it was making a new batch of ice every 30-60 minutes. The repair instruction video was a great help....made the repair a snap!