KBRS22KVWH2 KitchenAid Refrigerator - Instructions

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

got the new part, took the old part out and snapped the new part in! Very easy. Thank you.

I followed the video provided by PartsSelect and it was very good with almost every step you take. Pay particular attention to how the demonstrator stands relative to the frame and things will go a bit easier. There is one thing the video fails to do well and that is show you how the metal U-shaped rod is extracted. At best, the close-up gives you a clue rather than a sense of what is done and the verbal explanation of what it is you are trying to do with the screwdriver blade is unfortunately not detailed enough. I experimented as best I could with varying degrees of force and various positions but was taken by surprise when the rod suddenly was free and slid half-way out of the old frame. I still am not clear in my own mind what I did to free it, though I have my suspicions ;). Other than that step, the video took me through everything smoothly. One key - save everything from your old frame, you'll need it all!

Bought new crisper from Parts select followed directions on how to replace. Replaced in a bought 30 minutes.

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

with the freezer working I knew the compressor was working. I confirmed that the actuator door in the refrigerator was working but no air was blowing out. The hardest part was removing all the freezer drawer components and the ice maker so I could remove the panel in the back covering the evaporator motor. A quick resistance check of the motor confirmed no continuity in the motor. Take your time so that you dont break any of the snap in pieces. The motor I received did not look like the one I was replacing, but in fit in place and bolted right in. They provided an adapter wire to connect the wiring. All in all it was a fairly easy job. The video I followed was very helpful.

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

No tools required, but you must be careful not to shove or jam this kick plate into place as it is a plastic part and not really very sturdy. This is the second time I have replaced the kick plate and PartSelect has always been knowledgeable, polite, and helpful
!!

Motor evaporate. Replacement. Just like the video and it worked out perfect. Refrigerator works great now.

Removed rear cover, removed fan and than drip tray. install new tray and reassemblied

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.