JTP86SH2SS General Electric Microwave Oven Combo - Instructions

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Remove the microwave cover. Requires a phillips screwdriver and a torx security bit/nut driver (there are two security type screws on the back...guess they don't want you to do this at home!). I had to buy the a security bit set (about $7). The diode is easily accessible on the right side under the fan. Requires removing on small phillips screw and unplugging on electrical connection. GE provides some instructions in an envelope on top (after cover removed). There is a warning/instruction to discharge the capacitor before service. This was not a problem for me. Actual diode replacement took 30 seconds. Whole job = 15 minutes.

it was a simple screw in on both ends. no soldering

pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door

bought a fuse but that didn't solve the problem. Guess I need a new microwave

I unplugged the defective plug and replaced it with the new one. Took 5 min total

Lifted up the glass plate. Put in the new roller guide. Set the glass plate back in place. Repair done in about 30 seconds! Thanks for prompt service in sending the new part. My only regret is that the part was expensive, and I have already replaced it once before. The new part is still plastic so will probably need to be replaced again.

First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!

Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".

The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?

I think I could have managed with just the diode but since I had to pull it I decided to replace all related parts per my research. The Magnetron more than likely was fine.