JSS27GJ4 General Electric Range - Instructions

DIANA from TINTON FALLS, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

burner would not lay flat against surface of range.

Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.

Parts Used:

8 Inch Surface Burner

John from Westbrook, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Bad Burner

Removed trim ring and drip pan, loosened retaining nut and replaced the burner. I was very impressed at the fast service from your company. Thank You

Parts Used:

8 Inch Surface Burner

Donald from Farmington, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Bake element did not work

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

Parts Used:

Bake Element - 220V 2300W

Kenny from CALDWELL, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Burner rings and drip pans stained

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

Parts Used:

Tommy from Hydro, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Up to 1 hour for oven to preheat

Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.

Parts Used:

Bake Element - 220V 2300W

Joel from Avon, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

No Spin Cycle

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

Parts Used:

Screws - Package of 12

Richard from LORDSBURG, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner won't heat

Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the metal correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.

Parts Used:

8 Inch Surface Burner

George from Sarasota, FL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Bake element began to spark and short out when I tried to use it.

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

Parts Used:

Bake Element - 220V 2300W

Bill from MANHATTAN, KS
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Burner wouldn't operate

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Parts Used:

Range Infinite Heat Switch Kit

Linda from Hindman, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the items ordered replaced the worn out ones.

the replacement items fit really good. It was a matter of remove and replace,

Parts Used:

Carl from Morristown, N.J., NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

timer knobs broken off

I simply took the 3 new timer knobs and slid them on the metal shafts. It took less than 5 minutes to replace all 3 knobs. Now I can set the start, stop and time functions which have been inoperable for over 5 years. An easy and straight forward .

Parts Used:

Timer Knobs - Kit of 3

Christy from Danville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

replacing rusted drip pans on a 30 year old stove.

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

Parts Used: