JSS16PD1WH General Electric Range - Instructions

unplug it and plug the new one in

I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power

I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL

It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.

To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple

1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.

first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.

The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed the old burner bowls, replacing them with the new ones.

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!

The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.

I went by the video