JS645EL1ES General Electric Range - Instructions

THE TWO 8' ROUND HEATING ELEMENT
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.

Easy

popped the new one on!

I took off the cover of the stove with a socket 1/4 mm, screwdriver and pliers. Now it works perfectly. thanks.../

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.