JS48FWDWFA Jenn-Air Refrigerator - Instructions

took the old one out, put the new one in, reset the Refrigerator-Light 5 min. job. Tanks for the fast delivery B.Z.

Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.

Very simple. Unscrew old filter, following instructions on new filter's box, install new one by hand.

Carefully removed all of the screws to get to the compartment which housed the broken circular door that seals the ice compartment after ice has been delivered via the water fountain on the front of the refrigerator. Disconnected the wire harnesses (labeled as I went) and pulled the unit off of the fridge. It would probably be wise to have shut the power to the fridge off, although I did not. The problem was that the circular door that snaps back into place after delivering ice had severed one of the tabs that holds it in place. I discarded the old door and slipped the new door into place. There is an electromagnetic plunger that is responsible for the door opening when ice is being delivered (the system is magnetized and it draws the plunger in, thereby opening the door) and then snaps back into place once the ice button is released. I found the best way to get this back into place was to put the door (with its harness) into the "open" position and then gently force the plunger into place. Put everything together and all was good.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

Removed Control plate first. Second, I removed the next section behind the control plate. Inserted the new striker and reassembled.

I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

removed torx screws and replaced ice bin drive ring.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

The fan motor was burned up affecting the efficiency of the refrigerator. I removed the fan motor, tested it, ordered a new one and installed. saved 100 bucks in service call charge and got great service in delivery from parts direct. Ordered on Thursday and recieved monday.

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Had to replace ice bucket rack because auger motor broke the plastic backing and also the auger motor because shaft was bent on old auger motor. Just followed directions on web site to do repair.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect