JP34951WW General Electric Range - Instructions

Remove stove top from cabinet. surf for you tube videos to replace switch.

Remove screws from 2 sides of cook top, lift out top frame/glass assembly, element controls are to your right. Remove screws on top and bottom of element control assembly to access wiring and inspection. The 4 element controls, 4 heating coils, and all internal wiring were check for shorting, open circuits, and signs of burned parts. My trusty Fluke meter found a Halogen Element control shorted to ground. I order the part from Parts Select.com it came the next day Fantastic Service !! I'm happy, my wife's happy!

We never could figure out how to get the glass top removed to replace the burner. Looked at several instuctional videos and they never wrong in their description of where the 2 screws were to remove it. We finally called Sears Repair. They came out the next day and fixed the problem. The scres were on the side of the stove unit, not under the oven door. Oh well, atleast it works. Part select is excellent and I would use them again. This is the 3rd time I've ordered parts.

Turn off power from main panel that supplies unit. Basically, just pushed out the radiant cooktop from underneath (from the cabinet below) setting it aside on the counter, unscrewed 5 screws from each side which then let me pull apart the glass/ceran cooktop from the lower part (don't forget to remove the plastic knobs). Now I'm able to access the plate/cover in which the switches are attached to. After unscrewing the plate/cover (just a couple small screws on each end), I can now carefully one by one unplug the wire connectors from each damaged switch and attach to the new switch. Now, just swap out the switch and put everything back and you're good to go. It's really easy once you take off the glass/ceran top. You'll be able to see how they connect. Don't forget to turn the power back on.

turned off breaker feeding electricity to cooktop, pulled cook top out of counter top, removed screws holding glass to cook top, removed knobs, replaced switches, replaced everything in reverse order. before re-installing glass I turned power back on and tested burner for operation.

Raised cooktop......took 8 screws from trim plate and cook surface off.....removed 4 more screws off switch mount bracket, removed 2 screws from switch and mount bracket ( switch now free) ...pulled off wires and connectors one at a time, and put the wire on corresponding new switch location.... Took a total of 30 minutes.... Cleaned cooktop surface too! Cautions...don't tighten ANY screw too tight, as stripping will occur.

Cooktop lifted out without the need to remove any fastening of any kind. Slid two 2X2 sticks under top to have access to screws around perimeter. After removing all screws I lifted the glass top from base. I did all of this before I placed the order to make sure that I was ordering the correct element. Good thing that I did that because there are two similar replacements. I would have ordered the wrong one and the more expensive one had I guessed. The replacement unit has a wire lead with a insulated connector and a diagram where to install it. The original wiring connectors were plenty long enough to reach the terminals. Because of a slight change in the required connections per their diagram I decided to use the new wire, maybe a distance between terminals required the new insulated connector. Be careful when pushing the wire connections on the terminals, I pressed on the heat insulator ring and cracked it. Everything worked out great. The most amazing thing that happened, even though I ordered normal shipping, the element arrived in 24 hours. Can't say enough about Part Select.

Getting to the control switch was the hardest. Handling our 35" cooktop was tricky. The rest went fairly easy. Just make sure you make a diagram of the colored wires and where they go on the switch. We had to expand the holes in the switch a little to get the old screws lined up.. Putting the cooktop back together was easy.

Just follow the directions on the website.

Set cooktop circuit breaker to off.
Remove hold-down straps from underneath cooktop.
Lift cooktop from counter.
Remove screws holding glass top to base.
Remove screws holding switches
Remove two screws holding element switch.
Move wires from bad switch to new switch.
Reinstall.