Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This infinite control switch allows precise adjustment of heat levels for improved cooking accuracy. Smooth regulation enhances cooking performance and safety. Replacing a faulty switch restores dependable heat control.
Are you having trouble with your dishwasher's water flow? Perhaps it?s time to consider this replacement part - the Frigidaire Water Inlet Valve. Made specifically for specific models of Frigidaire di...
Dealing with faulty appliance parts can be frustrating. That's where our genuine GE Surface Element Switch comes in. This high-quality replacement part from GE, a trusted brand, helps regulate the hea...
Are cooking odors taking over your kitchen? Clear the air with our Whirlpool Range Hood Charcoal Filter. This dependable, genuine replacement part is a kitchen essential that helps keep your cooking s...
1) Turn Power off at Circuit Breaker 2) Lift Cooktop out of counter top. 3) Remove all dials from controls by pulling straight up. 4) Remover glass plate which covers burners by removing screws along outer edge. 5) Remove the two top screws from the control to be replaced (this holds the infinite contr
... Read moreol to bracket) 6) Remove one wire at a time from the old control and plug on the new one in correct orientation. 7) Reverse above order to reassemble.
(Note: Not all infinite controls are same PN when ordering, the drawingings are deceiving that they are)
Pulled unit from the counter top, removed all side screws holding the top on and set the top off. Removed switch mount section, Identified the terminal wire locations. I then removed the old switch and connected the wires per my diagram. Returned all screws, tested the burner for opeation and reset the cooktop back into the counter hol
... Read moree and secured.
You have to replace the switch if the shaft breaks (I think we hit it with a pot). This is a flat glass cook top. Turn off the power at the breaker box. I took the drawers out below the cook top and loosened the bracket holding the electrical conduit. That allowed me to push up the cook top from below. There is some adhesive but nothing h
... Read moreold it except its own weight and the adhesive. You do not need to disconnect the conduit. Remove all of the knobs. Remove all of the Phillips screws around the upper perimeter. Do not remove any of the hex screws yet. When all of the screws are removed, lift the glass cook top off of the metal "guts." At this point there will only be adhesive holding it on. Now remove two hex screws at each end of the control strip. Remove the two Phillips screws from the subject switch. Lift up the the control strip, disconnect the electric leads to the switch, reconnect the leads to the new switch, and then re-attach the new switch to the control strip with the two Phillips screws. Then go backwards. Replace the control strip and secure with the two hex screws at each end. Before replacing the cook top, check the burners. They rest on posts with small springs designed to keep them flush with the glass cook top. Make sure that all of the burners are properly aligned on their posts and springs. Replace the cook top and re-attach with all of the Phillips screws. Return the cook top to its resting place making sure the adhesive strips are correctly placed around the perimeter. Replace the bracket on the conduit. Put the knobs back on. Flip the breaker back on and start cooking.
