JIM158XBCX0 Jenn-Air Ice Maker - Instructions

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

I watched the film on installing and taking out. Step by step. easy.

Fast after a little help from a friend

Pretty much followed the how to video. Biggest pain was removing the screws to the bracket that houses the motor.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Watched the video that was attached to my order confirmation (great idea) and just followed it step by step. Real easy repair since I had tried to fix the noise first without ordering parts, so I knew what I was doing Did a temporary fix which quieted it down while I waited for the parts and then the repair itself was pretty straight forward.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

I found the part I needed on this website, watched the tutorial and saw how simple it was to do myself. I ordered the part and it arrived within a few short days. It took me no more than 15 minutes to change out the part. I saved myself several hundred dollars. It is rather shocking how much the "professionals" charge considering the cost of parts, labor and nominal service fees.

what I discovered is the condenser fan is still operating but not strong another word insufficient cooling for the condenser. therefore, it's getting too hot and shutting off and stripped the circuit breaker. After installing the new condenser fan, it gets back in business. it's quite simple. Just unplug the unit off, uncover the bottom back cover and there you see compressor, condenser fan and other good stuff. there you unscrew the nut in front of the condenser fan and remove the fan, then it expose the two screws that holding the fan motor, remove these screws and take out the motor. and just install the new fan motor kit in and there you have it. plug it back to the wall and there it goes

I've tried ordering the part from Sears and they told me it will take about 7 days for the part to arrive, some other place said it will overnite for extra money. So I've ordered the part from Part Select at a good price and prompt delivery. once the part arrive installing the part so so easy cause it had easy to follow instructions.

Wires in cutter grid were broken and wouldn't freeze/cut ice. Replaced with the new ice cutter grid that came completely assembled. Put it in with a screwdriver in less than 10 minutes. Ice cubes ready in 45 minutes. Repair guy told me it would be $455 for him to repair it. With shipping, mine was $133 and 10 minutes of my time. Well worth doing it myself.

Removal of old valve very easy and accessible, 2 screw/bolts for mounting, disconnect to electrical leads by hand, disconnect 2 plastic water lines with push/pull connectors and reverse order for installation. Total time-less than 5 minutes and basically no tools required expect pliers or nut drive to loosen screw/bolts. Just turn on and it was making ice

It was easy to remove the old grid and replace it with a new one.