JGS9900CDF01 Jenn-Air Range - Instructions

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

removed the two screws holding the burner to the cooktop, disconnected the wire clip from the electrode then removed worn out electrode from burner. Re-attached the new electrode to the burner, re-attached the igniter wire then put the burner assembly back onto the cooktop

Put a new one in.

Easy instal most of time was taking off and replacing back panel Found watching how to videos helpful

Just removed the shield (2 wing nuts) than the burner (1 Screw). THe back needs to be removed to unplug the igniter. I than reversed the process until I got to the plug and found that I had 2 male ends. I than had to remove everything and go back to square one until I find the part with the correct end (which should be Female) I'd check this before getting too deep into the repair.

Turned off the gas line & unplugged the oven. Pulled oven away from the wall to access the back of the oven. Removed the back panel (screws) on the oven & the few inner oven parts covering the broken igniter. Sprayed WD 40 on the threads of screws holding the old igniter in place. Removed old igniter screws with a nutdriver & unplugged it from the back of the oven. Installed the PartSelect replacement igniter & plugged it into the wiring receptacle. Reassembled the parts covering the new igniter & screwed the back panel back onto the oven. Plugged oven in, turned the gas back on & pushed the oven back into place. Tested the new igniter. Woohoo, oven works again & wife if happy!

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

Removed door, oven racks, and cover at the bottom. Very easy to get to the actual ignitor. The more challenging part is getting to the back of the oven where the igniter plugs in. Once we got the oven pulled out enough to access the bottom of the back panel, we removed the back panel....just a couple screws and it slides up. Unclipping and removing the old igniter was easy. It's a bit of a challenge to feed the new igniter's wires under the insulation and up over a small ledge and out a small hole that's smaller than a quarter. Small hands help. You can avoid the whole part of attaching it in the back of you clip the wires of your old igniter and new one. Then use ceramic wire nuts to connect the new igniter the the old one's wires. We decided not to do that since it was already done once that way and figured it would be good to have fresh wires clipped in at the back. Overall, fairly easy repair especially if you decide to connect the igniter with ceramic wire nuts.

It was very simple two Phillips head screws to remove the burner and one screw to remove the ignitor. It was probably less than a 5 minute job per burner. Unfortunately one burner had a very rusty screw holding the ignitor and the head stripped out. I tried a stripped screw removal tool with no success so I used a drill press to drill the screw out. It still took less than 30 minutes. Now both burners work like new

Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.