JGD8345ADW Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fan stopped working.
First I removed the two screws that hold the switch in place. I then pulled the switch out about 3 inches and disconnected the three wires from the old switch and replaced the new switch....
Parts Used:
-
Gregory from Hickman, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old grease filter had hole wore through
Pulled the old one out & inserted the new one. Less than five minutes.
Parts Used:
-
Michael from Mountain Iron, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
Parts Used:
-
Darrell from Moultrie, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace the grease filter!
-
Colette from Annapolis, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Parts Used:
-
Diane from Flower Mound, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rotten filter for down draft vent
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Parts Used:
-
Craig from Ashburn, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
terminal spade wrong size on range wiring to fit module
cut off terminals and replaced with the right size one's stove lights every time now wlrowe
Parts Used:
-
wilber from oshkosh, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
2 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Intermittent but rare spark when I went to start the rage: spark module definitely was toast or on its way out
The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..
Anyhow, thanks to the great part, the stove works really well again.
Anyhow, thanks to the great part, the stove works really well again.
Parts Used:
-
Bronius from College Station, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
5 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Parts Used:
-
David from Shelley, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Only two burners lit
Removed old igniter set replaced with new one. Hardest part was using the screw driver to removing the backing. Saved us having to buy a new stove since we just bough the house.
Parts Used:
-
Inga from Petaluma, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner was burnt out
-
James from McMillan, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
fan switch blew fuse & burned wires to switch.
take off frt of stove around burner knobs, remove old switch, put on new, replace frt of stove. Fast, easy & look at your savings!
Parts Used:
-
kathryn from batavia, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fan Switch burned out on Jenn-Air stovetop
The original fan switch for down draft stove top was discontinued! I found a replacement switch which worked just fine! I received switch and 2 different type replacement plates! One an exact match! Switch different but worked fine! I had to make no modification! Changed I'm about 10 minutes! I was lucky from what I read on other customers' responses!! They wouldn't promise me it would work!!
Parts Used:
-
felton from sunset, LA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Wore out burner and igniter
-
Bruce from Vashon, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gas burner would not light-had to use lighter
As described for the part. Easy repair. Easy to diagnose thanks to feedback from another customer of yours. Part was received super fast.
Parts Used:
-
James from Osage Beach, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!