Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.
The referigerator is warm, but the freezer is cold.
I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Ordered left side end cap from Parts Select. They sent me the right side end cap. Had to return the part. They did refund the part price but it cost me shipping both ways. Had to order the part from another vendor. After receiving the correct part it took 19 minutes to remove some shelves, replace the part and replace the shelves, deli drawer and deli cover. Very easy.
