JDR8895BAW13 Jenn-Air Range - Instructions

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

Removed 2 phillips head screws, disconnected the 2 wires. Installed new element, connected wires then installed screws. Took less than 3 minutes. What i liked was how fast I received the new element. Ordered online on Friday around 12:30 and received Saturday morning by 9:00 AM. Excellent transaction!

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

I removed the two small screws, gently pulled the element outward, slid the wire connectors off the ends of the element legs and reversed the process to install the new one. THE ELEMENT STILL DOES NOT HEAT. There must be a bad switch or thermostat at the ON switch area. That will be checked out by a Repair man as soon as I can get a schedule from him.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Make sure you unplug your stove before you start! You should probably shut off the power at the breaker box too.

Since the upper oven is so small, I found that I couldn't reach the connectors well enough to work with them. So I pulled out the whole oven, took the screws off the back cover and from the back I was able to easily reach where the wires connected to the element. Then it was a piece of cake.

Just use a small knife to unbend the little metal things that hold on to the metal ends of the element. Slide them on to the new element, and crimp them tight with pliers.

Oh, you also have to take off the bracket on the ceiling of the inside of the oven to get the old element out, and the new one in.

The oven has been working great!

Repair would have only taken minutes, but upper support plate screws were rusted and almost fused to the plate. Once the plate screws were out (had to pry plate out) installation was done in 3-5 minutes.

As for the replacement part, worked perfect on the first try. Very happy with price, speed of delivery and preformance.

I pulled the range out, unplugged it and removed the back panel with a Phillips-head screwdriver. I then removed the two screws inside the oven that holds the element in place. I located the two wires on the back of the range attached to the element. I gently pulled off the wires using a pliers and then easily removed the burned out element. I put the ends of the replacement element into the respective holes, screwed them in and then plugged the wires back on at the back of the range. After replacing the back panel, I plugged the range back in. I turned the oven on with an oven thermometer inside, to test it out. I imagine I saved at least a couple of hundred dollars for the repair with this simple DIY, if not, the cost of a new double oven range!

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

Turned off breaker to oven, removed racks, unscrewed the plate holding the element in place, and pulled out the wires a few inches. All easy and fine to this point. Never having done anything like this before, I wasn't sure HOW the element was attached to the wires, so tugged on them a bit, but nothing budged. Got a flashlight (it got dark in there with the upper part of my body in there)looked again, but still couldn't tell. Referred to this site and saw reports of "plug and play", went back and examined the ends more closely on old and new element, realized that they slide straight on and straight off in a "sleeve". Got some pliars and pulled the ends apart. Slid the new end on to one wire, but couldn't get the other one on until I realized I had crushed it a bit with the pliars. Reopened the "sleeve" with a vegetable knife and slid the other end of the element into the "sleeve" at the end of the wire. Then pushed the wires back in and screwed plate on. It took about 23 minutes, and that included time to look up this site and do some reading, jump up to find a flashlight, and jump up and find a pair of pliars. My hubby was out of town for 3 weeks and suggested I wait til he got home--glad I didn't wait.

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

I just bought my first condo and sure enough something broke in my oven. I thought "Oh great - I'll need to buy a new one..." After some research and a friend's advice - I was assured that I only needed to replace the broiler element. After researching the issue I googled replacement parts which led me to this web-site. I was amazed how easy and inexpensive it was for me to replace the part. The directions were easy, simple, and spot-on! The instructions that were provided were easy to follow. I also utilized YouTube instructions as well for additional visual guidance. The shipping was super fast and the element was packaged very well. Thank you so much!

Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wires, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!