JCD2297KEY Jenn-Air Refrigerator - Instructions

Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in the reverse order. It works great afterwards.

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

called jennair described the problem no help? they thought it might be the power board but it was not .. I put inthe new board same problem..so there is only one other component left the key pad!!! no thanks to the jennair I found the problem and fixed it....

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

Firts checked the parts received werer correct for the repair and the correct part numbers ordered. Then removed the ice bucket with the auger in bottom. Emptied ice from original bucket auger assembly. Checked out the removeal of the face cover for the bucket auger and removed it from clips that held it in place. Checked the specifications of the old ice bucket compaired to the new parts. Installed the aurger assembly into the new ice bucket and removed the two screws from the old unit to use in secure the auger assembly in the new bucket. The only tool needed was a 1/4 inch nut driver. Installed the face place on the new ice bucket auger assembly and tested the fit in the freezer. Ran test of the auger assembly without ice to ck for any misinstlled parts. Refilled the ice bucket with ice and tested with ice to complete the repair.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

Diconnecting the hoses was a pain as there are no instructions. Draw a diagram of each hose and color of the connectors or better take a picture before starting. Make sure the water is off, have a bowl & towels ready to mop up the water that runs out of the hoses. You have to push each hose in along with the little top hat connector that the hose runs thru. With both pushed in, hold the top hat connector down and pull the hose up and out. I could not reconnect without a leak on the hose that has a spring in it if I slipped the hose thru the white bracket. I ran the hose outside of the bracket and it went right in with no leak.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

First, I removed the bucket and drained all the ice from it. Then I took the ice bucket out and lifted off the cover of it which exposed the teeth that grind up the ice. I then removed these in succession and placed on my table so I could make sure I put back together appropriately. Once I had the bucket with everything off of it, I replaced and threaded the auger back through it so I could attach the end cap to it. Once that was in place, I put the parts back on the way I took them off. It really was a painless process and saved a ton of money versus calling a repair person. Definitely will use the service again. Very prompt delivery as had the parts 2-3 days after ordered. Well done.

unsrewed the back plate, removed three tubes. Then I removed old valve and replaced with new. Pluged two harnesses back in the new valve. Truned water on and checked for leaks and operated the filtered water tap and the ice maker. All went well.
I really like your site for the pictures included with the part, I like to see what I'm ordering.

I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.

Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!