JBP95AT1 General Electric Range - Instructions

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!

Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.

We ordered the part from Part Select, got it within a week and replaced the door.
It is a little tricky because one has to dismantle the entire door to do the repair (inside screw to undo).
You'd preferably be 2 to do the repair, although one can manage.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.

Piece of cake