JBP24WB6WW General Electric Range - Instructions

Very easy repair, Pulled burner coil out, removed old burner bowl. Put in new burner bowl, plugged burner coil back in... easy as 1,2,3

Removed burner element and put in bowl

Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer.

Removed all surface elements, threw away old burner bowls, put the 3 older surface elements back in place and inserted the new element.

The burner bowls look great. Now I won't wait so long to replace.

Thanks.

very easy..pull out burner, slide new one in..like a plug.

none of the "replacement" burner bowls i found at
store like home depot/ bed bath and beyond and such didn't fit.. so much for universal sizing..

thank you parts select.

a very satisfied customer

Pulled out burner and put new bowls in. Looks like a new stove!

Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.

Took 5 minutes to replace the 4 bowls. Ordered the bowls one day & they arrived the next day All went perfect.

Remove nobs from both switches.
Pull out the range (the hardest part).
REMOVE THE POWER PLUG FROM THE WALL
Remove 7 screws with nut driver and take off upper back panel.
Remove 2 phillips screws from front, they hold the switch brackets.
The new switches don't fit in the bracket so discard the bracket keeping the screws.
Removing 1 wire at a time from the old switch transfer to the new noting the letter/number ie "H1 P1" combos they are all there just not in the same places on the new switch.
When wiring is complete, using the bracket ,screws from the front screw on the switches.
Replace the back panel with 7 screws.
In my case the old nobs did not fit the shafts of the new switches. I found some at the local hardware store. I bought 4 for $0.29 each! I expect to be replacing the other burner switches shortly.

repair took about 30minutes total tiem..first turn off power to stove..then open oven removed racks..used nut drive to loosen top two screw hold element..then remove screw hold temp sensor element...then removed two screws holding broiler element...then removed the top screw ...then pulled element out about 7 inches to expose wire connection..held on with spade lugs.. pulled wires off...element now free to remove ...placed spade lug on new element...put element in pace with top two screws..loosely...then did rear screw that held temp element and broiler element...then tighten all screws ..turned on power..did 15 sec test to make sure wired properly..then 5 minutes to operating temperature... job done...hardest part was crazwling in and out the stove...old bones..

My husband had turned the oven on to cook something and didn't know that I have a plastic tray in there. Well, needless to say I needed to get some new oven racks. I tried to get them through the manufacturer (GE). They were 68$ each. I thought that was a bit steep, so I looked online. I decided to order through PartsSelect. Well...they can 2 days later (the week before Christmas!!)and were a PERFECT fit.
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!

Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!

unplugged unit pulled it away from wall took off the backplates traced wire to plug replaced with part ordered very smooth operation. the most impressive thing to me was i ordered part on computer and it was at my door in 30 hours awesome.

I removed the rear cover from the stove then removed the knob and two screws on the front panel that hold the control in place. I then took the wires off the old control one at a time and placed them on the new control. Then I placed the control in position and tightened the two screws on the front panel, replaced the knob and screwed the back panel in place.

Very easy repair. The gasket ends are stuffed into slots right below the oven window and the gasket is held in with small wire clips that pop into holes in the door. Just pull the old gasket off, no tools. Install the gasket starting by stuffing one end into the slot mentioned above until the first clip lines up with the first small hole. Then insert each successive clip into the corresponding holes. Then use a slot screwdriver to stuff the other end of the gasket into the second slot. No sweat.

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.