JB850ST1SS General Electric Range - Instructions

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Pull the old one put in the new one ... took about 20 minutes

Scary when stove burner comes on by itself, was turning breaker off for safety! GE website not helpful at all. PartSelect website enabled diagnosis of problem and then provided easy source for replacement switch. PartSelect has schematics: all I had to do is unscrew the back of control panel, unscrew offending infinite switch, hook up replacement switch same way, put panel back and done. GE service call starts at $80 and then who knows what kinda $$$? Did repair myself: cost just $38. Yay!

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Been procrastinating putting in the new element but decided to do it yesterday even if it meant eating breakfast out. Twenty minutes after starting , breakfast was cooking, at home on the new element. Two screws out, switch wires, snap on retainers, replace two screws and you're done!

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

After replacing the dual element and still having a problem with the range, I started troubleshooting the switch. Fortunately, our range has 2 dual burners, and the switches are the same, so I was able to move the switch and see the problem follow the switch (also, using a VOM, I could tell there was a short in the switch).
Since I'd already replaced the element, I only had to work on the controls, which are very easy to access.
I carefully documented all the connections (took a couple of pictures as well), and swapping out the switch took almost no time.
Lesson learned - follow the manufacturer's requirement to use only cookware with a flat bottom. This tea kettle only sat flat around the outside edge. That caused both the element and switch to blow. The "hot cooktop" light stayed on constantly, even after the element was replaced.

lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

Shut off power at breaker panel Took screws out of front of range top lifted it up propped open unplugged wires took off two clips holding burner in place hardest part of job checked wire colors to right places put clips back on pulled out light right next to burner replaced put top down replaced 3 screws turned peer back on hood to go

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.