JB840DP1BB General Electric Range - Instructions

Removed the two sheet metal screws securing the range top after disconnecting the power. Removed the mounting clips to the old range element and installed the new one. It was an easy fix.

very easy and clean.

Got a new knob.

First I found a u-tube video on how to repair this. I found the model number of my stove and used my phone to take a picture of it. I found the part on part select.com and ordered it. It came within a few days.
Turn off electricity to the stove. There were two screws to loosen and allow me to lift the glass stove top. It did not come off and we made a stick to hold it open. Then we unplugged and removed the old burner paying attention what was plug in where, maybe 4 plug ins. Then we clipped it back in, closed the top, rescrewed the top on. Turned on the electricity. It took 10 minutes to replace. Very easy!

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Changed out the burner with a new replacement and it still didn't work. The socket on the old burner had a burn mark on it. The infinite switch operated sloppy not crisp like the other burners.Ordered a replacement online. Moved the range away from wall and cabinet and shut off electric at panel box. Removed upper back panel. removed switch knob and 2 screws holding switch. Compared electrical connections of both switches and saw that they were different. Read instructions which were included with new switch and found diagram for connecting old lead to new lead correctly. After all leads were connected, remounted new switch powered up and tested OK.

installed new burner control w/knob. about 30 min. stove back in place. working fine

Open oven door, unlock hinges and lift off. Lay on face on carpet or piece of cardboard. Remove 2 screws at top that go thru door and hold handle assembly. Remove 3 screws on bottom that hold bottom door trim to inner door. Carefully turn assembly over (hold it together so you don't drop the glass front!) and place back on floor, hinge side down. Lift off front glass and frame assembly. Lay flat on floor. Remove 4 screws that hold bottom door trim to side frames. If glass is stuck to bottom door trim (which it probably will be from rust and gunk)..... Remove 4 screws that hold side frames to upper handle assembly and completely lift glass and bottom trim out. Holding glass vertical, stand on the bottom trim piece and carfully work the glass up and out of the groove (do not wiggle it side to side or you will need to buy a new piece of glass). While you have everything apart, clean all the parts and remove the decade of gunk. Reassemble in reverse. The long screws at the top of the door that hold the upper handle assembly in place, have spacers around them, they thread onto the screws and maintain distance and alignment when re-assembling. Also, I found it easier to remove the handle from the upper piece (4 screws) to allow me to lay the whole assembly flat while screwing the bottom, side, and upper trim pieces together around the glass front. Once that is done, then put the handle back on before you assemble it to the inner oven door. That is it !

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.