Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The center burner element of the large triiple burner was not working
The real challenge on this particular glass top range was to figure out which screws had to be removed to lift the glass top to get at the burner elements to do a replacement.
Removed the two side screws holding the control panel in place. Disconnected the two wire harnesses and took off the control panel to allow easier access. Then examined the screws attaching the vertical plate in front of the glass top. Most of them were on the on the vertical plate but a few were in the bottom of the horizontal plate. If successful, the vertical plate can be moved forward giving access to the glass top. You pull up on the front of the glass top and when it just clears the vertical front plate you pull the top forward a bit to get the back end of the top out of the read chrome vent piece. I then leaned the glass top up to about a 75 deg angle and then propped the top with a 24” wooden garden stake. I used two stakes to hold the top up. The challenge after that is to remove the old burner and carefully note the colored wiring and locations of the connectors and removed the three old clips. That took a bit of effort. several of the wiring harnesses were very short so you had to be careful when removing and installing the new burner. The burner has numbers stamped on the metal and you must note each number where the clips are located. The rest is to reverse the process. Some of the insulation pieces came off and some of the insulation clips fell off and you must be sure to get the insulation pieces back on in the correct location. Expect a lot of gunk that needs to be cleaned on the top and trim pieces. I save around $200 by doing my own replacement.
Actual temperature in oven was not consistent with the temperature setting
I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.
Oven door gasket was fraying and started to fall apart.
1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first. 2.) Pry up on each one of the retainer clips, they easily pop out of their slots. 3.) Work your way around the oven door gasket. 4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to. 5.) Take your new gasket, it should already have new clips, so you can throw away the old ones. 6.) Work your way around the oven door making sure the clips are nicely seated. 7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in. 8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it. 9.) All done!
Wife broke the interior window by splashing water on it while heated to 450.
Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.
Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year! Also follow the installation videos from PartSelect - very helpful!
I changed out the sensor and still same problem. Change out Thermosat and still same problem. I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation. Still need help. I’m an electrician and I don’t want to call a service technician and pay that big bill. Can anyone there help me out, if so please call. Ike Stanton 678-525-6644
The oven did not get up to or hold the correct temperature
This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.
