JB750DF2BB General Electric Range - Instructions

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Pulled the range away from the wall. Took two screws off of top cover with 1/8th socket wrench. Took small Philips head screw off the top, just leaned the cover away from the top. It still held in slots at its bottom so no need to drop it away from the range. Removed the dial from the front exposing two small Philips head screws. Removed screws, and pulled the comptroller away from the rear of the range. Held the new one in the same position as the old one and removed one connection at a time, and replaced them into the new part. Did everything in reverse to put it all back together. Believe me, easy as could be and you just saved $200 repair man cost. Part matched old part exactly.

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

Cut all power to the range. Easy to remove front panel and then screws and nuts that hold both white frame and glass top to range. Once the top can be lifted, cut the plastic zip tie that retains the harness. Unplug the harness and then remove the top. make provision for new zip tie before
the range top is re-installed. The range top is to be inverted for installing clips to the new heating element. Make sure that the holes line up to the pointed clips that hold the element. Not required to move the range.

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

I just followed the instructions on the link provided with the part

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

Thought it was the switch, being 2 of the wires were burnt. After troubleshooting, and determining the burner was getting power from the switch, but still not working, I ohmed the elements on the burner. There was no continuity through the elements. Checked the contacts in the temperature probe in the burner. The contacts were open, because the probe broke internally. Replaced the burner, and it all works now. Also replaced the switch, since it was burnt. Had to put new ends on the wires that were burnt also.This is the second time we had to replace this burner. The first time, the large burner element broke. Little disappointed that these burners don't last longer. We bought the stove new, but it was out of warranty when the burners quit.

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

1) REMOVE ELECTRIC PLUG FROM OUTLET. 2) Pull oven away from wall. 3) Remove the 3 machine screws holding in the top piece of sheet metal. 4) remove top piece of back sheet metal 5) pull knob of the front of the switch. 6) remove the two screws holding the switch to the front of stove. 7) remove wires (needle nose is helpful) one at a time and put them in the same location on the new switch. 8) put new switch into location on the stove and screw in the two front screws. 9) replace sheet metal on the back and screw in the 3 machine screws that hold it in. 10) plug in stove and move it back into position 11) put the knob back on the front and test it to make sure it works ok. 12) be sure to remove power if you need to do open the stove again to correct anything.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.