All Installation Instructions for General Electric Range JB650DF2BB

Heating element burned out

Followed example on YouTube! Very easy.

Parts Used:

Dual Radiant Element - 9 Inch

William from CONCORD, MA
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

F2 error when oven was heating up, along with a beeping noise and then it shut off

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Parts Used:

Temperature Sensor

Lori from Paris, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

fried oven control using raid

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Parts Used:

CONTROL OVEN TO9

Kerry from Loveland, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 13 people found this instruction helpful.

Was this instruction helpful to you?

oven was not getting up to temp

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Parts Used:

Temperature Sensor

walter from townshend, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

burner was inoperative

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

bryan from cocoa, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner not heating.

Isolated to control switch.

Replaced

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Jack from Greensboro, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

eye wouldnt come on

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

daniel from valentines, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Blew the electronic Control Board

It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.

Parts Used:

CONTROL OVEN TO9

PETE from MANCHACA, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Mother board was blown

Purchased the board installed it and saved about 130 dollars.

Parts Used:

CONTROL OVEN TO9

Kenneth from Bradenton, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Bottom Heating Element not heating up.

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

Parts Used:

CONTROL OVEN TO9

Wallace from Demorest,, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

oven control panel was blacked out..no clock no start.

Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.

Parts Used:

CONTROL OVEN TO9

Pam from Daphne, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

The middle of the element quit working.

Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.

Parts Used:

Dual Radiant Element - 9 Inch

Ruth Ann from New Columbia, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Pilot light out

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.

Parts Used: