IX5BBEXDS01 Whirlpool Refrigerator - Instructions

Remove the top two drawers, with a small screwdriver pop out module, unplug, plug in new module, press back into place, put drawers back, DONE! 5 minutes easy peasy ??

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.

Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anything with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemaker and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

First I turned off water supply. Then removed the two screws that attach ice maker, then disconnected the wiring harness.

Attached new ice maker in reverse order.

We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemaker and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.

WITH PATIENCE! removal of door and old seal no problem! Followed the video- very clear. The part was difficult. Ornery plastic that needed to be softened and clipped (in comes the hairdryer and vaseline)- First corner great! the other 3 -patience. we set the door on a folding table with a towel on top to prevent scratches and ability to slide it around . inserting the dense plastic flange to clip under the seal was the most difficult . i approached the insertion from the opposite side so I was PULLING the seal into place with the base of a putty knife.( instead of my pushing fingers-70 arthritic- use tools to help!!
It took bit longer, a challenge- can be done, I am so happy i don't have to look for a new refrigerator!!!! Thank you for that instructional video which gave me the courage for the repair.

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in less than 24 hours from my order placement.

Very simple fix, remove 3 screws, two connectors to the old switch