All Installation Instructions for Inglis Range IVP33800

Bottom element stopped working

Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.

Parts Used:

Oven Bake Element

ArLinda from ALTON, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

R/Front Range Element would not change to Med or Low setting. Stayed on full hot and burned food.

I disconnected power cord from house current. Removed back panels (2). I then removed round knob on front of range. I then removed the 2 screws holding the switch in place. After doing that, I gently removed the actual switch itself from back of face panel. I then separated the 2 elements of the switch.

I took new replacement switch and reinstalled the 2 parts of switch and placed back into hole in face panel. I reinserted the 2 front screws that holds the switch in place. I put the selection knob back on. However, the knob does not fit tightly. The shaft on the switch itself is to long, but the switch works fine. You do not even know that knob sticks out further than before. I plugged unit back into house current and tested range element to see if it works. It did so with no problem. I then replaced rear panels and secured all screws back to their original location and that was all there was to it.

No problem. Was a fast and effective installation.

Parts Used:

Surface Burner Element Switch, Large Burner

John from KENNEWICK, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bake element was broken

Remove the old part and install the new part.

Parts Used:

Oven Bake Element

Range Screw (Grnd Wire / Back)

Alexander from LINCOLN, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner didn’t work right

Replaced switch. Works right now.

Parts Used:

Surface Burner Element Switch, Large Burner

Ralph from MARION, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

the fastener became loose and dropped into the stove

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

Parts Used:

WIRE

George E from OCALA, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

burner plug broken

Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.

Parts Used:

Range Receptacle Kit

Norman from Newport, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Used part

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

Parts Used:

Drip Bowl - 6 Inch

Chrome Drip Bowl - 8 inch

Sabrina from FREMONT, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

could not control the temp of the element

take off back panel, simply unplug the old switch and plug in the new one. Simple

Parts Used:

Infinite Switch - 6 Inch

Steve from GREENBRIER, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

the oven temperature was not working right. I installed a new oven sensor. Works get now

Watch the video...

Parts Used:

Oven Sensor

Rosalind from APOLLO, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

temp level uneven

after watching the video, installed the temp sensor. Super easy

Parts Used:

Oven Sensor

Paul from HARMONY, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Cooktop on and cooktop hot indicator lights stayed on.

Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.

Parts Used:

Infinite Switch - 6 Inch

MICHAEL from FOUNTAIN INN, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Element temperature inconsistent

Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on

*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*

Parts Used:

Infinite Switch - 6 Inch

Nathan from WHITE RIV JCT, VT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

element not working properly

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Parts Used:

Broil Element

PHILIP from NORTH PORT, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner wouldn't regulate temperature

Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes

Parts Used:

Surface Burner Element Switch, Large Burner

Michael from THE VILLAGES, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

oven light kept burning out instantly

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Parts Used: