IRT138FDM00 Whirlpool Refrigerator - Instructions

This was an easy repair.

First I turned off the breaker that supplies power to the refrigerator, then I followed instructions to remove the old ice maker. I removed the bottom screw and loosened the two top screws and it came out easily.

The only unexpected problem I ran into was that the connection at the refrigerator end was 'hard wired', i.e., the wiring harness was not removable from the freezer.

After disconnecting the wiring harness from the old ice maker, all I had to do was plug the wiring harness into the new unit, slide it into place, then replace the bottom screw and tighten the two top screws.

Turned the power back on and had ice within 1/2 hour! : )

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making all the ice we need thanks

joan mcquain

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

unscrewed 4-5 screws; unplugged; attached arm; installed; reverse pattern. truly easy. cost 1/3 what repair man quoted me. this is easy!

Removed one screw on cover covering wires on old ice maker,disconnected plug, removed ice maker, checked connector to make sure there was120vac, Power supply was good, installed new ice maker, connected plug. Works great.
Part to fix ice maker is very expensive, complete unit only $15 more and it has a one year warranty.

First removed 3 screws and took out old ice maker, punched out water inlet tube area in new ice maker connected the electric and screwed it back in. Within an hour...heard the ice drop. (I did not do the repair, my boyfriend did, however I think I could have done it.

With a little investigation, I found that the ice tray had corroded, and the increased friction was keeping the ice from dumping out properly. It also had apparently damaged the gear motor, and the timing of the ice ejector was off. I went to the Part Select site and found that the icemaker specifically for my refrigerator was significantly more expensive than the universal Whirlpool replacement icemaker, but the two looked similar, so I ordered the universal replacement. When it arrived about 3 days later, I was able to easily remove the standard parts and replace them with the plastic parts and wire harness that were unique to my refrigerator. They fit perfectly, and I had the new icemaker installed in only about 20 minutes, including time spent to remove and replace the plastic parts

The ice maker is held in by three screws. There is an electrical connection. Also, there is a water line to the rear of the unit.
The replacement unit had clear instructions and a selection of parts to match the defective device.
Hint: don't discard the old unit until the new unit is configured for installation.
Turned on the water and the electricity to the fridge, and had ice in several hours.

remove inside cover. meit ice collected, remove old part and install new part. about 1 hr.

Removed two screws, pulled the element out and disconnected the wire harness. Reversed the procedure and we were one.
Kept a close watch n the ice maker to make sure we didn't have another flood. The first time an ice cube stuck between the metal bale and the side of the freezer--we had about 50 gallon of water on the floor. Thought we had it fixed and a few days later another flood. Decided to replace the unit and it is working great...Hopefully no more floods.

I just removed three screws from the old ice maker and disconnected a single set of wires. All I had to do was reconnect the new set of wires and screw it back into the side of the freezer. Anybody could do this repair.

$80 part motor fan replaced saved me $1000 or more on new fridge.

Called in and you guys helped out
You guys are the best.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.