HWA2506W Hoover Washer - Instructions

took off back small metal panel, tilted washer front side down, easy to put into place after removing old part

Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys

I replaced both the pin and the hinge. The old screws did not fit these parts nor did either of the parts fit the other part although they were almost identical. Screws should be included with the parts as these are supposed to be replacements. Do not try to order only a pin or a hinge without the other. Delivery was very quick.

Viewing the video on how to replace the hinge pin was very helpful orienting me on how to get the job done. As I viewed the video, I thought to myself, "It couldn't be that easy!" Once I received the part in the mail, which was received quickly, I followed the video instructions in finished the repair in 5 minutes. It was a great experience and gave me a new online parts distributor that I will use in the future since I am a born "Do it Yourselfer." Thanks.

clicked on how to do it yourself on the part and video showed how to change it.

I found the parts that needed replaced on the Parts Select web sight.I clicked on see install video icon for replacement of the parts that needed replaced and that made the repair real easy.

I used a putty knife to depress the holding clips under the front of the lid, then raised the lid to access the screws . Using a phillips head screwdriver I removed the screws holding the hinges and removed the door/lid then after removing the screw holding the broken pin, removed and replaced it with the new pin. and reinstalled the two screws on the hinges to reinstall the lid, and snapped the top back down. The whole thing took me less than 10 minuites to accomplish.

I watched the video first. It was correct except for the tool was not a phillips screwdriver, but a torx drive. Rounding up the tools took the longest. Everything else was just like in the video.

Watched and followed the video

Easy to remove broken part. Found rust, so after cleaning I applied paint (I let dry overnight).

By manipulating the washer drum, moving left and right, the screws were easy to get to. However, to get the screws back in took tightening by strong hands. Plus, found that the lid sensor had worn out, so that was adjusted.

New screws would probably make the job easier.

All is fantastic and I found it was "easy" to replace with finishing help from strong hands.

Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!

I had my son remove all of the old hardware with an allen-key wrench. He then proceeded to install the new hardware. Fisrt he installed the pins on the lid. Next, he installed the hinges to the washer, leaving each hinge loose. Finally adjusting the lid until the screws for the hinges were completely tightened.

I popped the clips on both sides of the top with the putty knife. Raised the lid. Unscrewed the one screw on the old hinge. Screwed on the new.

It took a PhD in hinge replacement to do this.

I had to pop the top of the washer which is hinged in back. Raised it up and removed old hinges. replaced "hinges and hinge pins. It works like new.
Thanks for your "website". It was very easy finding the parts I needed.
Sincerely
Bill Hines

Once the machine was unplugged, I used the paint scraper to release the top of the washer by inserting it at right front and left front about two inches from the sides. The spring clip's were released and the top swung back on the rear clips . The lid hinges were exposed , removed and replaced with the the screws from the original parts, "as they do not" come with the replacement parts.
"Replacing first one side" then taking the lid and replacing the parts (pivot parts) attaching the- 2nd lid hinge piece at this time as they will not go together in any other fashion. Snap thewasher top down to close. I would suggest spraying a little silicon spray occaisonally, to avoid the parts failing prematureily. All told about 20 min. to do the job. Don't forget to plug in the washer!