HTW200ASK1WW Hotpoint Washer - Instructions

Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.

Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great

First, I made sure the washer was empty of cloths and water and then unplugged the appliance. I laid a towel down on the floor just in case there was any water remaining in the drum and I slowly laid the washer on its side, I was able to do this with the drain and water hoses still connected to the washer, be careful you do not rip any of these connections or simply disconnect, to each is own. Once I had the washer on its side, I used the socket wrench to remove the 3 bolts holding the belt drive cover on the motor. I placed the cover and bolts to the side, and I began pulling off the old belt that had slipped, stretched, wrapped and ultimately hung up the motor off buy unwrapping it from the motor itself. Once the motor was free from the belt, the wheel was able to spin like it is supposed to. I installed the new belt by simply wrapping it on the motor wheel and spinning it on to grab onto the second wheel, just make sure to line the belt up correctly so it does not fall off. I placed the cover back over the belt and bolted on the 3 bolts. I flipped my washer back up and ran a small wash cycle to make sure that the belt was working properly and once it began to wash, I threw in some cloths and began washing as normal. The whole process took less than 15 minutes.

Disconnected power and water, laid it on its back, took off the belt, then took the new belt and put it on with a little difficulty putting the belt back on. really have to watch your fingers if you are not careful

Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.

easiest repair I have ever made. No problems and was surprised as to how fast and easy it was to repair. I did not need two of steps the instructions stated I had to do. best purchase I have ever made.

Disconnect water lines.
Remove top control panel.
Remove 2 screws & disconnect wires & replace old for new

Unplug machine
Move machine out from wall
Removed 4 screws on back plate
Removed the 2 screws holding the assembly to washer
Pulled old unit out and reversed process to put back together

But when I went to test it would not drain tipped washer up and removed hose from motor and found a sock inside
Remove sock and washer runs great.

Just a note this website was very helpful in finding the right part with the exploded view of parts

Thank you

Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well

any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly

After loosening top screws on back ,snaps in front,no need to total remove top changing springs you have to reach below top of case with vice gripes and attach to spring rod about 8 inch down and lift up (tuff for 80 year old) tap down on plastic retainer, turn retainer 1/2 turn so hook will slip out ,now lower spring it will fall out of bottom retainer. Now for reinstall ,instead of vice gripes on the spring down inside case with no room , by hand take new (correct color) spring reach deep inside and install bottom into bottom retainer now take old spring run long end hook threw retainer hole in top case, hook to hook ,now you can pull new spring easy out the top about 3 inches and now vice gripes above case with enough room to reinstall top retainer remove gripes now only 3 more to go

I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.

I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.

Watched You Tube and had at it. In the end it was fairly simple.

Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!