Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This drive belt is an authentic OEM part that is compatible with various models of washing machine. The drive belt is responsible for allowing the drum to rotate smoothly during the wash and spin cycl...
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in y...
This is a water inlet valve; an electrically controlled solenoid valve that opens and closes when necessary, to control the flow of water into your washing machine during the washing cycle. This part ...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation...
Maintain stability and reduce operational noise in your washing machine with this right-side suspension rod and spring assembly, designed for select GE models. This component supports the wash tub and...
Having trouble with your lawn mower's belt tensioning? This Husqvarna Idler Pulley Assembly might be exactly what you need. The job of this vital part is to keep your mower's belt tension just right. ...
$24.13
In Stock
Order now and your part arrives by Mar 30
Questions And Answers for HTW200ASK0WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
15 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Daniel
December 17, 2019
Timer will not advance to 2cd spin cycle on any setting will advance up to it then stop at end of 1st spin cycle and go to done light up
For model number HTW200ASK0WW
Hello Daniel, thank you for your question. It sounds like the timer portion of the UI & CONTROL BOARD Part #: PS12730586 is failing. We would recommend replacing that part. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lynn
June 19, 2022
Is it hard to replace the suspension rods on this machine
For model number HTW200ASK0WW
Hello Lynn, thank you for writing. There is the Right Side ( red) PS12343378 and the Left Side (blue) PS12343379. We have a video that is for a different model, but should still serve as a valuable guide. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hi Arcadio, thank you for contacting us. Based on our understanding of the issue, we would recommend checking the drain hose if it is clogged or jammed. If that is not the case, then you may have a faulty drain pump assembly, part number PS12723115. The drain pump assembly removes water from the washer during the drain portion of the cycle. We would recommend replacing the drain pump to fix the issue. Good luck with your repair!
some times it stops in the middle of washing close. some times it works fine. caught spin light flashing. Could this be because the rod and spring need replaced? what are the symptoms to know the rod and spring`need replaced?
For model number HTW200ASK0WW
Hi John,
Thank you for your question. If your washer stops mid-cycle, there are some parts that you will need to check to see which one is causing the issue. We recommend checking the electronic control board and switches, the lid switch, the drain hose, the pump and motor, and the water inlet valve. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
My washer doesn't seem to be filling. I can hear water sprinkling in for about a minute then the cycle starts. Does this machine have a water level switch? Also having a problem with imbalance.
For model number HTW200ASK0WW
Hello Paul, Thank you for the question. The Water Level Switch is part of the Washer Control Board, PartSelect Number PS12730586 so the Board will need to be replaced. We hope this helps.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
