HTS17BCMBRAA Hotpoint Refrigerator - Instructions

I FOLLOWED YOUR VIDEO............WAS EASY. THANKS

I replaced the fan motor and one of the grommets. When I took the motor out it was clear it was failing because there were metal flakes from the motor on the fan blade. I followed the instructions on the posted video. My model did not have a removable bottom tray in the freezer so that was one less thing to do. Aside from that the video was accurate. I had two minor problems during reinstallation. First, it was very difficult to get the spring clamp back on the fan blade without pushing it against the motor. Recommend you get someone to help hold the spring open while you push it on. Second, the length of wire on the replacement was not exactly the same as the original and I had to move some wires around. Recommend you take a picture of the cable layout before disassembling.

Fast and easy-great video instructions for each part ordered.
All parts perfect fit.
My refrigerator is running like new again-good for another 10 years!

Followed the instructions on the repair video and it made very easy. Also saved us a lot of money. Thanks for your help.

We have an older model refrigerator and thought it would be impossible to find a replacement ice bucket for the freezer. Not only did you have the exact part but it came unbelieveably fast. I would use your website again!

I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.

p.s. I didnt use any tools, but to satisfy you I select nut driver.

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.

Despite attempts to quiet the 2 year old fan, I went ahead and replaced it. Part Select was prompt with a new one at my door less than 24 hours. It was just the fan motor, so took a couple extra steps to place it in the metal housing, but no problems and though the frig still makes noises, it's not coming from the fan as before.

I pulled the refrigerator away from the wall and turned off the water to the refrigerator and unplugged it from the wall. After removing the icebucket from the freezer I located the mounting screws, loosened them, unplugged the electrical connection below the icemaker and carefully removed it from the freezer. I unpacked the replacement icemaker, matched it against the original and attached the electrical connection adapter. Using the slots provided on the new icemaker I placed it over the mounting screws after aligning the water inlet pipe properly. I tightened the mounting screws while maintaining the icemaker in a level position. I plugged in the electrical connector. Then I replaced the icebucket, plugged in the refigerator back into the 110VAC outlet, turned on the water and repositioned the refrigerator in it's normal position.

First I removed the two screws, the fan and unpluged the electrical connection. Then, plugged in the new part and then screw it back together.

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

Went on YouTube and it had excellent instructions for removal and installation

two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge

I opened the fridge door removed the tape the customer had on it to keep in place. Gasket was super worn out I pulled in it to remove it. Cleaned it where the new gasket was gonna insert. Put the new gasket in place and with my thumb applied some pressure till I heard a small snap. Did the same all the way around and closed and opened the door to check it all around making sure it was in place and sealing all around.

Open freezer, remove rack....this got a little complicated because I had to remove the door, that required the offset screwdriver because I had a clearance issues preventing the door from opening all the way. Remove the panel covering the fan, unplug the fan, remove it from bracket, install new fan, plug in, replace panel, replace rack, replace door...bam all done!