HTN16BBSXRWW Hotpoint Refrigerator - Instructions

Very easy. Bought a 6-1 screw driver for 1/4” and 5/16” nut drivers ends. 4 screws to remove panel that covers evaporator coil and motor. Remove the foam piece 2 screws, unplug wire plastic clip and motor come off. 2 screws to remove from bracket, replace motor. Put back together and reinstall. Watch video - it helped but very easy to do even if you don’t watch common sense is all you need.

Removed the cracked rails in the door and snapped the new ones into place.

My husband did the repair in 45 minutes and said it was very easy. The video made everything plain and simple.

I wouldn't have tried it without the excellent YouTube video that gave step-by-step instructions! I set up a laptop next to the refrigerator and watched each step then did it myself.

The instructions were very detailed and all of the parts looked exactly like what I was seeing. The only difference was that I didn't need to remove the floor of the freezer to get to the fan motor.

I bought the fan motor, grommets (2), compression ring and fan blade because I wasn't sure which part was causing the problem, and figured that as long as I was in there I might as well put in all new parts.

As it turned out, I did not need the compression ring, because the new fan blade came with a compression ring on it. This was different from what was shown in the video.

Since doing the repair the freezer is now as quiet as it should be, which is a great relief. The project and the money spent were more than worth it. It was great not having to pay a repair man to do the work!

The video that was attached to the part order was good, but not exactly the same as my unit. One thing I recommend is that you cover up the drain below the evaporator coil with a piece of paper and tape it down, because as I was putting the motor back I dropped a screw and it fell down the drain. So I had to go buy a new screw.
Give the cost of a repair man coming to fix a refrigerator that cost only $450 to begin with, doing this repair was well worth my time. (But I also had another refrigerator to move things to and could take my time and wait while they replaced the faulty part they shipped me.)

Located the model number on the inside wall of the unit. Wanted to make sure to order the correct product.Because of the age of the refrigerator I ordered the rubber mounting grommets. In this model the mounting frame is built at an angle that makes the removal and reinstall very easy. Remove two screws and the motor is loose. The fan blade easily pulls off the shaft of the motor . Clean up the fan and reassemble.

Well the repair would have consisted of simply removing the old fan, and installing the new one, however, the replacement fan sent had a female connector on it, when it should have been a male connector. So, I had to take the connector off the old fan, and splice it onto the new one. This turned a really simple job into more of a project, which I was not planning on.

unplugged appliance. removed cover from back of fridge. unplugged wiring to condenser. pulled fan blade from motor. removed two bolts from fan bracket.removed fan blade and then motor. cleaned fan blade and all surrounding parts.installed new fan and blade. plugged fan motor back in re-installed cover on back of fridge.plugged fridge back in.motor is now nice and quiet.

Started removing screws until I got to the fan (it's easy). Then just took out the old fan and put the new one back in the same way. The only challenging part was putting the clamp back on the fan, but I finally got it. The fridge is finally quiet and we can sleep again! PartSelect made it really easy and they were incredibly fast. Thanks!

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

First, I love that fact that my new fridge piece came in the mail in 2 days! I didn't order it as a rush, but I'm so glad it came so quickly! The installation could not have been easier! It took me longer to clear off my broken vegetable pan cover than it did to pop the new one in. My overall experience was amazing and super easy! I'll be back to PartSelect should I need I need to replace anything else in the future.

new cover slipped right in place, however, the way the new one is designed, the hump in the front rubs the bottom of the door. you have to make sure you push the door shut or it will remain open .

I took out the old shelf and popped in the new one. Took 1 minute or less. The delivery was in 2 days! Amazing experience! My refrigerator feels brand new.