HTH18GBC2RWW Hotpoint Refrigerator - Instructions

Open the freezer panel which attached with screwws and locate the defrost thermmostate behind the back pannel. Cut off the old thermostat wires and connect the new wires.

Easy

I first washed old shelf to make sure glass will easily slip out. Installed old glass and replaced.

I ordered the new part from PartSelect and it was delivered very quickly. I removed the part from the box, laid the old glass shelf inside if it and placed it in the fridge. No tools required, and then slid the vegetable drawers into it and replaced the food. Very satisfied with my purchase experience.

Was only two screws after that carefully took the part away unplugging the wires at the same time was plugging in to the new part and was done after 5 or 7 min

The overload protector was the problem. It plugs into the side of the compressor and the run capacitor plugs into it.

If you pull the overload protector and it rattles when you shake it, that's probably your diagnosis.

The replacement is different from the original and the wire connectors are different. Hold the thing in the same orientation as if it were plugged in. The vertical connector goes to the neutral wire, which on my fridge is orange. The horizontal connector is for the overload, which for mine is black and white. If you have a schematic you should verify the wires yourself.

Anyway, the refrigerator now works like new.

Went right on

replaced lights in refrigirator and freezer

My husband did the repair in 45 minutes and said it was very easy. The video made everything plain and simple.

The video that was attached to the part order was good, but not exactly the same as my unit. One thing I recommend is that you cover up the drain below the evaporator coil with a piece of paper and tape it down, because as I was putting the motor back I dropped a screw and it fell down the drain. So I had to go buy a new screw.
Give the cost of a repair man coming to fix a refrigerator that cost only $450 to begin with, doing this repair was well worth my time. (But I also had another refrigerator to move things to and could take my time and wait while they replaced the faulty part they shipped me.)

I wouldn't have tried it without the excellent YouTube video that gave step-by-step instructions! I set up a laptop next to the refrigerator and watched each step then did it myself.

The instructions were very detailed and all of the parts looked exactly like what I was seeing. The only difference was that I didn't need to remove the floor of the freezer to get to the fan motor.

I bought the fan motor, grommets (2), compression ring and fan blade because I wasn't sure which part was causing the problem, and figured that as long as I was in there I might as well put in all new parts.

As it turned out, I did not need the compression ring, because the new fan blade came with a compression ring on it. This was different from what was shown in the video.

Since doing the repair the freezer is now as quiet as it should be, which is a great relief. The project and the money spent were more than worth it. It was great not having to pay a repair man to do the work!

Removed the cracked rails in the door and snapped the new ones into place.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Started removing screws until I got to the fan (it's easy). Then just took out the old fan and put the new one back in the same way. The only challenging part was putting the clamp back on the fan, but I finally got it. The fridge is finally quiet and we can sleep again! PartSelect made it really easy and they were incredibly fast. Thanks!