HTDP120GD1WW General Electric Dryer - Instructions

Very easy fix since it was only the knob

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.

Very simple. Ordered the part. Received correct part and fit perfectly.

Used a flash light to see, reached in and installed new bulb above the door

I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

First I took the system apart which I did not have to do. However, by doing that I was able to figure out which parts make the timer run. Anyhow, you simply place the new timer knob on the small shaft and it worked like magic. It was very easy to do.

Just took off old one installed new one. It came right on. Thanks

Ordered & received new Timer & Knob. Disconnected dryer from power.
Located screws on back of dryer console & removed screws so console could be tilted forward.Used cell phone to take picture of timer with connections to keep track of where to reconnect wires. Unsnapped connections to timer. Removed old timer and attached new timer. Attached new knob to front of console. Plugged dryer back up to power and tested by turning new knob. Reattached console with screws. Done!

the original knob had cracked and I ordered a new one and replaced it, all is well, thank you

No brainer

I took off the old dryer knob and put on the new one

Just placed it where it belonged.

I pulled the old handle off and pushed the new one on.
No problem at all.

Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.