HDA2000V00WW Hotpoint Dishwasher - Instructions

placed the end cap into location and forced it into place. Fixed -and we are all much happier!!

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

Used drill and easy out to remove broken part, then put in new one

The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

Put end cap in dishwasher with movable part toward the back of the dishwasher. The free end of the movable part should be oriented at the top of the end cap. Put the lower half of the end cap into the rail behind the indented metal area so the widest part of the end cap is just opposite the hole where it should snap into place. Push the movable arm towards the back of the dishwasher until it fits under the upper rail. Then move the top half of the end cap into place under the top of the rail.

Opened package, removed cap and screwed it in place.

This is the second time I have order a part from this firm. They have been kind, helpful and sent my order to me immediately. The first part was a wheel for the dish rack in the dish washer. The second part was an end cap for the dish rack slide. I installed the parts within a minute. I am very pleased with their professional service and highly recommend them to anyone with an appliance problem where parts are needed quickly.

I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.

It was so easy-just popped the end peice in and it fit perfectly. I also ordered 2 knobs for my dryer which was only one year old, they were also so easy to put on.. I received my parts 2 days after I ordered and because of some problems with my computer had to talk to the operators and was very pleased and happy with their help and with the parts that I ordered. I wil always order my parts from Parts Select.