All Installation Instructions for Gibson Washer GWS1749CS0

I had no problem

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

Parts Used:

Washer Lid Lock with External Safety Switch

Albert J. from Homosassa, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Belt Had Smoked

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

Parts Used:

Drive V-Belt

Millard from Grand Prairie, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

bad belt

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

Parts Used:

Drive V-Belt

Craig from Clatskanie, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

burning smell from wash, needed new drive V belt

watched the video on website, printed instructions for feedback.

Parts Used:

Drive V-Belt

Joseph from Trinidad, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

bad rumble when running

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

Parts Used:

Tension Idler Pulley

Herbert from Randolph, ME
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

Was this instruction helpful to you?

Stopped spinning made noise

Changed the belt started working like new.

Parts Used:

Drive V-Belt

Cecilia from Moreno Valley, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

worn belt

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

Parts Used:

Drive V-Belt

Karrie from Boulder, WY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Washer would flood out the floor now and then

One day the washer would spill water out on the floor then it would be fine for a week and do it again.Finally it broke,i ordered the new drain pump and installed it in just a few minutes,Hose clamps were a pain,it works just fine now,I would say replace the clamps while you are doing this ,it would make it much easier .Hope this helps !

Parts Used:

Drain Pump - 120V 60 Hz.

tony from wilmington, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

When the washer was filling up with water it would not stop and overflowed. This only happened once.l I called Frigidaire & was told I needed a new agitator & could replace it myself.

My Son replaced Dual Action Agitator & said it was easy. He did it in 15 minutes.

Parts Used:

Dual Action Agitator

Elaine from Dania Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench set

Was this instruction helpful to you?

Not Draing Water

Good

Parts Used:

Drain Pump - 120V 60 Hz.

Sammy from Notasulga, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

The water would not drain or spin out all the way

Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.

Parts Used:

Drain Pump - 120V 60 Hz.

sherry from ellenburg depot, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

old belt

Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.

Parts Used:

Drive V-Belt

Joseph from Landing, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Washer won't drain

My wife done the repair while I was out of town. She never tries to won't on anything in fear that she will mess it up.But she said she had it fixed in ten minutes. Just take the hoses off the pump, unplug, and unbolt where mounted. Then reverse to put on new one. Partselect is always very prompt to sent my parts and I have never had an issue with anything. I will buy all my parts from them from now on.

Parts Used:

Drain Pump - 120V 60 Hz.