GUD27ESSM1WW General Electric Washer Dryer Combo - Instructions

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

The repair was easy. First I took out 2 screws. Then I lifted off the top. Next I unscrewed 2 to take off front. I leaned off the front and reached in got out old gasket. Replacing new gasket went right around top front panel under the clips. Putting front on and returning 2 screws. Then Same for top. Dryer runs and sounds like new. Thank You for your quick mail and easy help?

I used these two videos to help me clean the inside of the machine, then change the drive belt.

Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.

Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.

very easy

Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.

Watch the video on how to replace the belt on PartSelct site belt installation page.

Unplug the dryer. On the back, I unscrewed the top three screws that hold on the instrument panel and (from the back) slide the panel to my left to disconnect from the top. I opened the dryer door and removed the two screws on the inside top of the doorway to remove the top panel of the dryer. Inside the top of the dryer are two screws to remove so that I could swing the front panel of the dryer out to replace the lower front felt drum seal. I needed to use wd-40 on these screws. When the panel opens, there is no way to disconnect the wires to remove the panel, so I had to prop it up with something so it didn't tip over and damage the wiring; a sturdy chair worked. Then, I heared the drum pop off and drop down a little. I replaced the seal according to the video; by putting it in the groove and pressing it down into the tabs with a flat head screwdriver or something smooth with a little of the seal hanging over the groove at each end. While I was in there, I cleaned out the lint and the wd-40 I used earlier. Then I closed the panel, lifting the drum back into place, ensuring that the dryer drum would turn before and after I replaced the screws. I replaced the top panel and the screws inside the dryer door and slid the instrument panel back into place and replaced those screws. The dryer works great and very quietly now!

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

inserted the latch into the opening in the front face of the dryer

Removed door strike and latch, replaced, works like new.