GTW538ASW0WS General Electric Washer - Instructions

There's two nuts on the back of the washer holding the metal backplate. I used my 11-1 Klein screwdriver. Once you get the screws out lift the backplate slightly and pull the whole top assembly out of it's spot and lean it forward onto top of the washer.

Take pictures of where the wires go so you can remember for later.

Disconnect the two wires and remove the two screws holding the metal plate. Same size nuts driver as the other screws.

Remove the sensor by just wiggling it out.
Slide the intake assemby out of it's spot.
Slide the new one in.
Then just do everything you did in reverse.

Takes 10 minutes. Super easy.

Removed the center agitator to clean it - had black mold and pink soap scum buildup underneath that you couldn't see or clean without taking it apart. Removed the bolt with ease. Upon tightening the bolt back in place, the bolt sheared in half, leaving the lower half threaded in place and the head in the socket. Had to use a drill bit and drill out the lower half of the bolt completely. Ordered the replacement bolt and reassembled everything in less than 5 minutes. Replacement part was perfect - hopefully it lasts longer than the original bolt.

I contacted parts select and entered washer information and asked them if they thought they would now what the problem was and and they responded with a answer and also a list of two parts that they thought might take care of the problem. I ordered the parts,looked on u tube to see how to change them and replaced both parts .I think the clutch was good but the drive belt was stretched and needed replaced.Know it works great.

IF you do the same repair, SAVE THE LITTLE O-RING that is inside the old part where the temperature probe stick in (If that is indeed what it is). It's chrome in color. New part does NOT come with that O-ring

Unplugged washer and hoses. Removed 4 screws in back control panel and 4 screws holding control panel down. Drained capacitor and checked that. It was good. Pryed washer top off with screw driver. Used vice grips to remove old and install new spring rods, replacing them one at a time. While lid was off I cut a small diameter pool noodle in half and cut 4 half noodles the size of each side. I unclipped one side of the tub cap and ran an 11" zip tie through the hole in the middle of one side and back up and out where the tub skirt and cap meet, then tied the half noodle to the edge of the tub cap and snapped down cap. Then repeated with the other three sides. I did this so heavier clothes, if they got out of balance, would continue to spin. The noodles keeping the tub from moving too far out of balance. The rod springs helped with lighter loads but still shut down spinning with heavy clothes. The machine always handled heavy clothes for 7 years until the last month or so. If it breaks with the noodles, I'll get another new machine.

You have to take the top off of the washer and the four suspension rods are at each corner. Fairly simple removal and installation of the rods. A quick you tube search is all it took. Easy peasy.

Extremely easy. You will need a helper to make it easy. The best directions are on you tube.

The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.

Replaced water pump. Washer now works as new.
Wife is now happy!

Easy fix. Take out the two screws on the backside of the control panel and remove control panel out of the way. You will need a long shaft nut driver or 1/4 inch socket extension to be able to get to the nuts, one on each side of the back of the control panel. The water inlet valve is right there in your face. Easy to remove and replace. Remember to save the small O-ring in the center of the top of the valve and reuse it. Oh, by-the-way, shut the water off first and unplug the washer. Replacement part was a perfect match.

Took the belt cover and then replaced the pump. Did a dry run and everything was fine.

Installing the inlet value was very easy the only thing was a very small "O" ring wasn't supplied with the value, so I removed the one on the leaking value. Not care must be taken not to damage the used "O"
The washer is running with no leaks
Thank you, for, saving me hundreds of dollars

Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy.
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!

1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!

Take cover off use socket driver to remove two hex head machine screws. There was a foam piece attached to the old part that i pealed off and attached to the new part. It’s there to prevent rattles. There is a tube that pulls out of the old part and a grommet inside that must be removed and placed in the new part. Connect the two electrical plugs and install the new part just like the old part came out.