GSG25MIPDFWW General Electric Refrigerator - Instructions

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

just put them in the proper shelves

I agree with the other posts that suggested taking a picture of the blades and spacers before taking the auger out, makes it so much easier to put it back together in the same way. The only difficult part was holding the two tabs apart while removing the unit, you need a second person to help with this. I used two small screw-drivers to gently pry the clear plastic box away from the white plastic holder, while my helper pulled the holder loose. Keep in mind that the plastic nut that holds the auger in place is a left hand thread. Went back together very easy and it's working great.

I am a 64 year old woman.I will 65 in March. I do the plumbing and painting at our house and my husband who is 67 does the carpenter work, I help him by holding boards he is sawing etc. I though the job would be easier than it was, but it was still easy. I took out the first screw which was in plain sight, secound screw I could not get to, and thought oh no I will have to take some other things apart. but when I removed the screw to the ice maker shield it was easy to slide it down out of way, and I got to 2nd screw pretty easy, I removed 2nd screw put new slide in place put screws in place started 1 st screw, then 2nd screw then went back and tightened 1st and 2nd screw, put the ic maker shield back in place tightened the screw slide ice bucket back in place, and though now this will be ready for company coming for the Holidays.... YEAH....

removed freezer door / shelf /ice maker pulled back panel off and removed fan

After shutting off the h2o, I unplugged the refrigerator. Using the nut driver, I removed the cardboard backing. Then I removed the fitting where the inlet line to the ice maker and pried the old tubing from the unit. I then undid the clasp about 1/2 way up the back and removed the section that went through the back to the ice maker.
I then reassembled everything and plugged in the refrigerator as well as turning on the water.
Keep in mind that because h2o and electricity are involved. MAKE SURE THERE ARE NO h2o LEAKS.

The first repair 2 years ago was due to the plastic auger that moves the cubes forward had broken. Recently we had began to notice small piece of plastic in our ice water. Finally the plastic piece that keeps multiple cubes from falling through the chute broke. I decided this time just to replace the whole auger and bucket assembly. Pulled the old one out... put the new one in, and alot less agravation than replacing parts.

1. I unplugged the refrigerator/ freezer
2. Turned off water supply
3. Removed the screws that held the cardboard skirt in place
4. Unplugged the water tube from the push connect
5. Removed the screws around the water inlet to the ice maker
6. Remove the water fill tube
7. Install new water fill tube and put all the screws and plates back where they go

I removed and cleaned out the ice tray, then removed the ice auger. Next I had to remove the front cover of the tray that housed the crusher, this was done by removing to screws on the bottom and sliding the crusher section, once the crusher section was removed I simply slid off the crusher cover and replaced with the new one and put it back together. It was that simple.

unscrewed lamp and replaced it with new one!

I followed the partselect videos for the temp sensor and defrost thermostat and the refrigerator has been working well for a about a week now. The refrigerator is old enough that I was just going to replace it. When I called the repair company I use, they said it would cost $200 to $300 for the repair, but I didn't want to put that money into an old refrigerator. I did a little research, found this site and figured it would be worth buying about $20 in parts and giving it a try. I have absolutely no experience working on refrigerators, but the videos were so easy to follow, everything went smoothly. The old thermostat was definitely broken when I checked it with a meter, so I'm pretty confident that the problem is fixed.

Replace the motor fan on condenser and clean the condenser

I followed the video and things went well. Glad I had the video.