GSE23GSKKCSS General Electric Refrigerator - Instructions

Watched a parts.com video on how to change defrost thermostat and followed the instructions

Replace the motor fan on condenser and clean the condenser

Followed steps found on YouTube. The only missing instruction was to remove the small retaining clip from the water tube inlets to allow you to press the retaining circle down to release the tube

Never did repair. Parts ordered on April 3 and not received by April 18th! Email sent to customer service on 4/16/20 requesting full refund. To date no acknowledgement! Will not order from PartsSelect again.

The water dispenser was not working, but when I pressed the lever I could hear it attempt to disperse water. But when looking inside I could see that when I pressed the lever it was spewing water from the tank. I was not certain why it was not dispersing water, but I knew I had to replace the leaking tank. I found several YouTube videos that described in detail how to replace the tank (and I highly recommend doing that). The removal and replacement was very straight-forward and that part took only about 30 minutes. But the time-consuming part was cleaning behind the refrigerator and cleaning the inside as well (since I already had most of the shelves out). Then once I got it all back together I tested the water dispenser and still nothing. So I disconnected the line coming out of the tank going up into the door and then tried again. This time water was coming out of the line. So at that point I was fairly confident that the problem was a frozen line somewhere in the door. After leaving it unplugged for a while and also heating the door with a hair dryer, I connected the line again and got water dispensed.

First I disconnected the Power from the unit. Pulled out the freezer drawers and the ice machine used a 1/4 inch nut driver and removed the sheet metal from the back of the freezer exposing the evaporator coils. I defrosted the coils. Then I removed the two screws holding the defrost heater braket assembly and removed the two electrical connections from it. I then installed the new heater put everything back together(reverse of installation)and it works like a brand new fridge and freezer.

After shutting off the h2o, I unplugged the refrigerator. Using the nut driver, I removed the cardboard backing. Then I removed the fitting where the inlet line to the ice maker and pried the old tubing from the unit. I then undid the clasp about 1/2 way up the back and removed the section that went through the back to the ice maker.
I then reassembled everything and plugged in the refrigerator as well as turning on the water.
Keep in mind that because h2o and electricity are involved. MAKE SURE THERE ARE NO h2o LEAKS.

1. I unplugged the refrigerator/ freezer
2. Turned off water supply
3. Removed the screws that held the cardboard skirt in place
4. Unplugged the water tube from the push connect
5. Removed the screws around the water inlet to the ice maker
6. Remove the water fill tube
7. Install new water fill tube and put all the screws and plates back where they go

I am a 64 year old woman.I will 65 in March. I do the plumbing and painting at our house and my husband who is 67 does the carpenter work, I help him by holding boards he is sawing etc. I though the job would be easier than it was, but it was still easy. I took out the first screw which was in plain sight, secound screw I could not get to, and thought oh no I will have to take some other things apart. but when I removed the screw to the ice maker shield it was easy to slide it down out of way, and I got to 2nd screw pretty easy, I removed 2nd screw put new slide in place put screws in place started 1 st screw, then 2nd screw then went back and tightened 1st and 2nd screw, put the ic maker shield back in place tightened the screw slide ice bucket back in place, and though now this will be ready for company coming for the Holidays.... YEAH....

First I removed the two screws, the fan and unpluged the electrical connection. Then, plugged in the new part and then screw it back together.

Received the part in a reasonable amount of time. Installed super quick.

Simply assembled both pieces and inserted this additional into one of the shelf slots in the freezer. There is now extra space to store frozen food.

Using my putty knife, I slid it under the light cover prying upward to remove it. I then unplugged the the light board from the wire and unsnapped from the two prongs. Then reinstalled.

Open freezer, remove rack....this got a little complicated because I had to remove the door, that required the offset screwdriver because I had a clearance issues preventing the door from opening all the way. Remove the panel covering the fan, unplug the fan, remove it from bracket, install new fan, plug in, replace panel, replace rack, replace door...bam all done!

Went online to Parts Select and using the information that was provided found my part. The bin arrived several days later and was installed following the instructions that came with it. Simple to install by aligning the bin with the door push in and down. Which is the reverse instructions for removing one of the bins. Less than five minutes