GSC308PJQ3 Whirlpool Microwave Oven Combo - Instructions

Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going

Once we figured out to use small allen wrenches in the small holes of the hinge to enable us to lift the door off everything went smoothly. Took out six screws, lifted out the hinges - inserted new ones, replaced screws and replaced door. Yipee

XLarge pizza tray in a 450 degree oven - slam the door & CRACK. Replacement glass arrived on Saturday - VERY FAST DELIVERY. Placed 2 allen wrenches in both hinges - open the door half way & lift up. Place the door on a towel. Removed 6 screws, lift & seperated the inner oven covering, removed the broken glass & cleaned inside & replaced with new glass. More time was spent cleaning & coming up with a tool to fit into the hinge

Thanks for the excellent service. Parts cheaper than local stores, arrived on time, with NO PROBLEMS.
Installation, probably 30-minutes. Took the opportunity to clean glass, door panels, etc while disassembled, so used about an hour. Oven cleaner was a big help in the cleanup.
Very rewarding project and it saves changing the unit and and refitting the countertop.

PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.

Followed a video. Followed instructions

unscrew cover
remove old bulb
screw in new bulb
replace cover

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.

Originally ordered just the spring assuming that might be it and it was the cheapest way. However after getting in I found that the latch assembly had a broken 'tit' that is intended to hold the metal latch in place as it moves. Attempted to glue w/ epoxy but as i expected there was too much pressure to hold it in place. So....ordered the assembly.

TURN OFF BREAKER.....

1) Remove the two side rails by removing screw on the inside bottom of rails.
2) It helps to remove the door to get it out of your way but not required. To do this open door fully and insert two nails or similar into holes on each hinge. Close the door until the hinge contact nails. Lift the door up and out.
3) remove the top control panel by removing screw on either side (outside of oven)and screws on the underside of panel behind upper door.
4) It help to completely remove the panel to have more room to work but not required. If you do it is a good idea to photo the cable locations so it is easy to recall where they go. For the most part they only fit one location but always a good idea.
5) remove the latch by removing all spade connectors and two screws in front.
6) place new latch and reassemble.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

Removed old racks, installed new racks. Recycled old racks.

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

Quickly