GS475LEMS3 Whirlpool Range - Instructions

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

exchanged old with new

Watch the video...

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Removed trays to expose the ignitor, replaced ignitor and re-assembled.
Would be much faster the second time.

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

very easy watched the howto you gave

The repair went well. Only took a few minutes. Oven is 21 years old and still working. I figured why throw away if still working. Thank you Select Parts for coming to my rescue. Will keep you in mind.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Turned off power to range. Removed the lower panel that was secured by two screws, as well as the metal cover beneath it also secured by screws.. Removed the two screws securing the igniter, and pulled apart the black tubing that secured the igniter. (I had to pull hard to get it apart). Plug the new end into that same black tubing. screw in the two screws to secure the new igniter (this is tricky because one screw is hard to reach) I laid something in the base to cover the holes so I wouldn't lose a screw if it dropped. Screw metal panel back in, followed by the lower oven panel.

Took out old one but electric hook up fell in the hole had to fish it out also dropped a screw in the hole could’ve find it used a different one