GS2125CEEW Maytag Refrigerator - Instructions

First I removed spill tray. It slipped right out. next I removed the front cover.it had 2 screws hidden by the spill tray. next were the 2 screws holding the selection slider.Under it is 3 more screws after removing them then the assembly will come lose from the refrigerator.Be careful you dont drop the ice door. unplug the assembly. Turn unit over and you will see the limit switch remove and replace it with 1 small phillips screw. remove and replace dispenser actuator pad.replace everything in reverse order.The ice door is the only thing a little tricky.still i replaced ours in about 10 mins.

Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.

Emptied the door by taking out all the shelves with their contents. Removed the upper door closer works. Removed the door by lifting up and away from the main box. Layed the door on its side. Took out the old lower hinge pin and door closer with cup. Put in the new lower hinge pin and door closer with cup. Applied sewing machine gear grease to the 2 pieces where they work together. Lifted the door and placed the lower hinge pin into the door closer with cup. Replaced the upper door closer works.

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Replacing the hinge pin itself is really easy. Most important is to brace the bottom of the door before replacing the pin, otherwise the door will drop as the bottom hinge must be removed to install the new pin.

A couple of short lengths of 2x4s used to brace the door bottom worked fine. With these in place the door did not drop down after removing the hinge. Replacement of the hinge and pin easy.

I removed the screws that held the control panel in place. Unplugged the wiring cable and put the control panel aside. I removed the old broken part and inserted the new part. Very easy. Put everything back together and it worked like new.

took off the covers and put in the new part and then put it back together.

Removed 2 screws for front cover lifted front cover straight up to remove.Removed 2 more screws to remove ice door assembly, replaced ice door. Refrigerator should be unpluged before doing any of this to avoid getting shocked.

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

I couldn't have repaired the refridgerator at all if your web site didn't have photos along side of the parts. My parts no. was destroyed. But after removing the face plate on the ice dispenser door and checking the area behind the plate, the burned part was clearly identifiable. I removed the one screw holding it and the two connecting wires - and pulled out the tiny switch. On your site, I entered the refridgerator number, and the parts list (300 or so parts for this model) appeared with identifying photos of each part. All it took was to order the part (and the ice door simply because it was old) and put it in when it arrived in one day! No only did I save much cash, but I left with the confidence that I knew what went wrong. It works as good as new now. Thanks!!!!!

Unplugged the refrigerater from the outlet. Took off the front ice and water dispenser assembly. Disconnected the front panel from the electronic board. Removed the ice and water dispensing cone and installed the plastic/Foam insulator door between the two plastic arm frames.

Removed two star screws on plate, then two chute screws which allowed me to remove the chute. Then I removed the two screws which held the assembly in place, we had to pullout the assembly about three inches. (I had my wife hold that out of the way) Then I reached in behind the assembly and removed the chute door. At that point I saw that the tab which hold it in the opening mechanism was broken off. So I reassembled everything without the chute door and put a dishcloth in the chute to keep the cold in and the heat out. (during this time we had to manually take ice out of the hopper) I then went on line to partselect.com and ordered the part. It came in 3 days and my wife and I opened it all up again, snapped the chute door in place, removed the dishcloth, put the assembly and plate back together and it works like new.

First I removed the three screws in the top hinge that hold the upper right corner of the door to the body of the unit. Then I just lifted the door off of the refrigerator. I proped the door up just long enough to pull out the old pin (plastic) and put the new one in place. Next I picked up the door and set it on the new hinge, and last I put the three screws back into place. It has taken me about as long to type this out as it did to actually make the repair. The part was also very reasonably priced so I purchased two since this items has been replaced previously.

looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change

rl