GLHT188WHB2 Frigidaire Refrigerator - Instructions

My freezer was frozen but my refrigerated side was not cooling, the temp was actually around 60-degrees. After inspecting i noticed no air was flowing through the vent from freezer side to fridge side. I removed everything from freezer and took the back wall panel off inside freezer section and immedietely noticed alot of ice on coils etc. After researching i found the defrost timer was not working and thus allowing frost and ice to build up on coils and block air flow. My defrost timer was located on the front bottom left behind kick panel, using a phillips screwdriver i removed 2 screws and then disconnected wire harness to the defrost timer. Then i inserted new defrost timer and connected wire harness and then put the 2 screws back in. My fridge is now working great and the ice build-up is gone and i am getting good air flow .. temps on fridge side are now between 32-34degrees. This was an easy project and saved me alot of money doing myself

I simply snapped in the new part. It took a few seconds. I would like to say that I found the part using the model number of the fridge. When I went to look at the description it said the part was 26 inches. The one I had was only 24 3/4 inches. I called you guys and was told that this was the correct part and to ignore the measuement.
You were Right! the part fitted perfectly.

My evaporator fan was not working. This fan is located in the freezer section, (top), behind an access panel at the rear. Part of it's job is to blow cold air down into the fridge. At first I wasn't sure if it was the fan itself because after the fridge was unplugged an plugged back in, the fan would run for about 5 seconds then quit. So..I tested the auto defrost timer by manually cycling it with a screw driver, it was fine. I bypassed the defrost thermostat switch, no difference. Finally, I cut an old extension cord and connected it to the fan, it was the culprit.. It didn't run on 120. It did spin for a few seconds on initial power up only. After reading that this model may also have a flakey defrost thermostat switch, I ordered both the fan & new defrost thermostat switch. It was a very easy install for both items. No directions are needed, it's obvious when you get in there. Mine is runnng like a champ again.

I removed the filter casing containing the casing, removed the filter and replaced it with the new filter and screwed the casing in place tightening with the wrench.. It took less than 5 minutes and was the easiest replacement Ive ever done.

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

To simple to explain. I was very happy with my parts and prompt service,,

Reviewed the video on your website and followed the directions to the letter. Great video

This was a really easy replacement job, but it did not have any directions. The main thing to know is to really "warm" up the new gasket before installing so that it can easily be fit into the door of the refrigerator. Some recommend putting it in warm water, but it's pretty big & I didn't have anything to put it in, so I used a hairdryer to soften it up. It also takes a few days for it to "form" to the door. When I received it, the top right had a seem split, not an actual "rip" but it looked like the glue did not stay to connect the edges very well. I called and Part Select issued a refund and got a new one out to me the next day! Great company!

First, I replaced the defrost timer, really easy, 4 screws popped the cover of the electronic area (top of refrigerator compartment) took it out and plugged in the new time. Unit still would not defrost, so replaced the thermostat as well. Bit harder, removed ice maker, 2 screws, back plate from freezer, 4 screws. Thermostat was clamped to a copper tube- the original had one of the wires hanging out of it- cut the wires and crimped the new wires on, shrunk the plastic tube with blow dryer over the wires (taped them for good measure) and so far so good. Learned most of this through these tips, so keep reading if this isn't your problem, just save myself $1000 on a new refrifgerator...

Really, really, really easy:
1.Unplug refrigerator (electrical safety).
2.Remove cardboard cover at bottom of refrigerator (two short self-tapping bolts) with a wrench.
3.Pull old fan blade off fan motor shaft (just held on by a compression fitting--no tools needed).
4.Push new fan blade on shaft.
5. Replace cardboard cover.
6. Plug in refrigerator, write nasty letter to Frigidaire.

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

Replaced the old bins with the new bins...The most important part of the story was finding this website and locating and ordering the necessary components...that was amazing - a few clicks of the mouse and my new parts were on their way.

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

since I had my fridge since 2003 it seems that I've gotten my moneys worth but it has worked flawlessly with no issues. I did not want to part with it so I troubled shoot the system and realized that it could have been number of things so I just decided after reading some reviews here on this site I decided to just purchase the items that would be effecting the fridge not working properly which was the evaporator fan, defrost thermostat, defrost timer, temperature cold control thermostat, I also cleaned the condenser coils in the back of the unit so they can be able to withdraw heat from the unit. my repair and installation took about 4 hours due to the cleaning of the coils but now the fridge is working like brand new. thanks to this sitt and it's comprehensive video tutorials on installations and repair it my job a lot easier to do.this is not my first time ordering from this site and will not be my last. anyone considering ordering from this site do not hesitate there are great with parts and customer service.

It takes a 1/4 " nutdriver to take one screw out that holds the cover over the water filter. You have to come up from the botton of cover. Then take two water lines off housing , by pushing the round collar back toward the fitting,and pull fitting off housing. Then take the two screw out that hold the housing on. Make sure you have the water turned off before you start.