GLDS560GD1WW General Electric Dryer - Instructions

Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.

Snap off and then snap New one on.

My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.

just replaced the unit handle and how my wife can open the dryer without a screwdriver

removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.

Used online instructions. Worked well.

loosened two hose clamps and four screws to replace the anti siphon valve.

as per your instructions. The copy of the directions was very hard to read

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

Had a repair shop quote 230 for repair . Spent 66 on parts and did the repair in 45 minutes using the instructions from folks on this site . Very happy with results thanks

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

- Removed two screws at top left and right of door.
- Removed top dryer panel
- Removed two screws holding front panel in place
- Noticed drum slide was missing because front drum bearing was worn away and slide had fallen off.
- Went ahead and removed drum to replace rear drum bearing (probably not needed; should have disassembled it first to discover this). Would have been better to pull drum first (loosen idler pulley and release belt, pull drum straight out) instead of attempting to unscrew bearing. Be sure to note how the idler pulley is set.
- vacuumed tons of lint up
- Replaced bearing (needed a second person for this; drum too big to reach around. be sure to pre-thread the bearing)
- Ordered front drum bearing, waiting to repair it now, should be good after this.

Pull the old lint trap out. Slid new one in