GJC3034HB0 Whirlpool Cooktop - Instructions

Got Model and SN, went on line and located correct part. Ordered part, arrived in 3 days. Started repair by turning off power to stovee top. Got putty knife and went around edge to loosen stove top to raise and het to underside to dismantle cover. Used battery drill to remove screws on cover. After accessing and removing top and bottom, removed 2 screws, changed one wire at a time and replaced on new switch, reassembled in reverse, turned on power and happily watched burner come to life with new switch.

Called an authorized Kitchenaid service technician after ordering part. This was the second time this switch has required replacement so we saved time and money by ordering the part in advance from PartSelect. The trickiest part of the repair was separating the ceramic top from the rest of the cooktop. Had we attempted to do this ourselves, we would have given up at that point. I would only recommend this as a do-it-yourself repair if you are intimately familiar with how these cooktops are put together. It is fairly easy to break the ceramic top if you're not.

First I found a YouTube video for Maytag Range Repair – How to replace the Surface Element with Limiter - 6" - 1200W

The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge

2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.

3. Take a photo of the element being replaced for wiring connections.

4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both

5. The clips have to be removed from the old element and put on the new one. Place them in the same locations

6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element

7. Put everything back together in reverse order.

Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.

Verified via ohmmeter that one of the two burners was open and not working. I also tested the switch and that appeared to be working okay. I then took out the old unit and compared it to the new one, and found that they upgraded the new unit. I followed the instructions to match the labeled parts and move the wire to the newer location of that. i.e the old one had 2B and 2A at the top and 1B and 1A at the bottom. The new one had 2B and 1B at the top and 2A and 1A at the bottom. It did come with wire extenders and insulated tubes on top of them, and extra to cover additional. After a couple of tries, I decided which wire I needed to use on which (small connectors to match small, and large to match large.) In a second try I decided to flip it over to have it face up instead of down. Overall, it worked out very well, and I was very pleased when I did the power up test and everything worked as desired.

looked on internet on how to remove top. an easy fix after watching video

The new element wiring placements were totally different from the old element. Lucky for me the lettering printed on the terminals for each pole was the same as on the old one. It was just a matter of matching up each terminal pole lettering. The instructions that came with the new element were of no help at all. Youtube was my best helper.

My dual zone burner would trip my breaker anytime i tried to turn it on. All the other burners would work fine. I searched online and found a way to test my burner, which was shorted or grounded out. I purchased a new burner from the site...It was as cheap or cheaper than other sites. It showed up a few days quicker than i was expecting..I also replaced the switch to the burner, just as a precaution and to save time since i already had the top glass off of my burners....EASY JOB!

Followed the instructions in the video provided by PartSelect, which was very accurate. They only problem I have encountered is that the wiring from the old element compared to the new element do not match up 100%. I had to call Whirlpool today and schedule a Tech to come out and see if they can resolve the problem. Right now, when the burner is turned on, both the inner and outer elements turn on.

Very easy just followed manufacturers instructions.

I decided NOT to crawl under my stove top to find the correct model no. of the unit, as recommended in the Help section of the website. Instead I just guessed. It arrived, and of course didn;t fit. So I crawled under the stove top, got the correct model no., and instantly found the correct part to order. Part Select instantly honored my request for a refund on the first part and the correct part is on its way. So I ended up paying two delivery charges instead of one. LESSON LEARNED.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Pulled old knobs off and replaced with new knobs from PartSelect. I'm glad they had them, no one locally had them available.

Thank you. Have been looking in stores for knobs to no avail.

Followed the instructions in the switch kit. Unpluged range glass cook-top power cord. Lifted smooth cook-top out of counter hole. Removed about 10 sheet metal screws around box/glass surface interface. Removed all 5 infinite control power switch knobs vertically. Lifted glass cook-top from element box. Set cook-top aside on edge away from work area. Flipped switch control box cover and identified which switch was to be replaced. Noted colors and terminal post data. Replaced 1 wire at a time per the kit instructions. Reversed procedures. Turned unit on and confirmed proper function. That was it!

I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.