GI7FVCXWB00 Whirlpool Refrigerator - Instructions

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

The only real difficultly I had replacing the ice door was getting the exterior trim off the freezer door. You have to push down on the bottom of the trim to release the tabs that hold it in place. After removal of the trim, the rest of the repair is pretty straight forward.
The ice door kit solved the problem!

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

Turn off the water to the unit. Disconnect the plug on wiring from the old valve.
They always recommend you disconnect the electric (unplug) the unit while doing this work.
Disconnect the water lines from the old valve by pushing the water line slightly into the flange on the valve, it releases the line from the flange.
Hold the flange rim against the valve seat and pull, you may have to jiggle the water line a little while pulling to remove it.
Push the water lines into the ports on the new valve, turn on the water and check for leaks.
If no leaks, plug the wire connections onto the new valve, reconnect it to the unit and turn the power back on.

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

I followed the video. If there is an exact opposite of handyman or mechanic, it would fit me. I don't fix things well and I have very little patience for fixing things.
I fixed this easy by following the video. The first side took about 30 minutes because I was super cautious. The second side took less than 5
minutes because it was really easy.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

When you open the box, have flat place prepared so you can lay the seal down to allow it time to relax. Only handle the seal by the corners. Lay it flat. I used a hair dryer to remove the creases during its time in the box. Keep the hair dryer moving, don't rush this step, take your time and allow the seal to relax on its own. Once it's completely relaxed. Remove the old seal by starting at the corners. No tools needed just keep working around the entire seal. Inspect the seal chanel and clean as needed. Pick up the new seal by the corners and press in place with your fingers, starting at the corners. I found doing the top first then the sides, leaving the bottom to last worked for me. Hope this helps.

Put new one on matching the sctew feet and design of the grill

Pushed on new one as directed online.

Popped out the old switch and replaced it with the one dying

I received the wrong part - had to pay returnin shipped and restock fee. Lost out on dealing with this company. Went to Whirlpool site and got correct light for my refrigerator

I just removed the old bin and hooked on the new one.

I watched a YouTube video real quick to see what I had to do and got to the job at hand. I removed the old gasket by pulling it out of the track and bring it around the front of the drawer. I wiped down the entire area where the new one would go and started inserting it into the groove, making sure it went in completely in on the bottom. I was done in less than 15 minutes. Super easy! This fixed the issue and the freezer door closes fully.

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.